763824

Ferm BSM1005 - FBS-1000N Manual

4
Zoom out
Zoom in
Previous page
1/20
Next page
5. VEDLIGEHOLDELSE
Sørg for at maskinen ikke står under strøm, når der
udføres vedligeholdelsesarbejder på mekanikken.
Maskinerne fra Ferm er udviklet til at fungere længe uden
problemer med et minimum af vedligeholdelse. Ved at
rengøre maskinen regelmæssigt og behandle den
korrekt, bidrager De til en længere levetid for maskinen.
Rengøring
Rengør regelmæssigt maskinkappen med en blød klud,
helst efter hvert brug. Sørg for at ventilationshullerne er
fri for støv og snavs. Brug en blød klud, der er vædet i
sæbevand til at fjerne hårdnakket snavs. Brug ingen
opløsningsmidler, så som benzin, alkohol, ammoniak,
osv. Den slags stoffer beskadiger kunststofdelene.
Smøring
Maskinen behøver ingen ekstra smøring.
Fejl
Kontakt Deres Ferm-forhandler, hvis der opstår fejl som
følge af slitage af en del.
Bagerst i denne brugsanvisning finder De en
reservedelstegning med de reservedele, der kan
bestilles.
MILJØ
For at undgå transportbeskadigelse leveres maskinen i
en solid emballage. Emballagen er så vidt muligt lavet af
genbrugsmateriale. Genbrug derfor emballagen.
Når de udskifter Deres maskinen bør De tage den gamle
maskine med til Deres lokale Ferm-forhandler. Der vil
maskinen blive bearbejdet på miljøvenlig vis.
GARANTI
Læs det separat vedlagte garantikort for
garantibetingelserne.
Vi erklærer herved, udelukkende på eget ansvar, at dette
produkt opfylder følgende standarder eller
standardiserede dokumenter
EN50144-1, EN50144-2-4. EN55014-1,
EN55014-2, EN61000-3-2, EN61000-3-3
i henhold til følgende direktiver:
98/37/EEC
73/23/EEC
89/336/EEC
01-03-2004
ZWOLLE NL
W. Kamphof
Quality department
CE
ı
KONFORMITETSERKLÆRING (DK)
Ferm 37
always ear protectors and dust mask.
• The sanding machine is not suitable for wet sanding.
• Check if the switch is not in position “ON”, before
you connect the mains plug to the mains voltage.
• Keep the mains lead always away from moving parts
of the tools.
• Use safety glasses, especially when you sand above
your head.
• Do not bring pressure to your machine, this will only
delay the sanding.
IMMEDIATELY SWITCH OFF THE MACHINE
WHEN:
• Excessive sparking of the carbon brushes and
verticiliosis in the collector.
• Interruption of the mains plug, mains lead or mains
lead damage.
• Defect switch
• Smoke or stench of scorched isolation
3. OPERATION
Always observe the safety instructions and
applicable regulations.
CHOICE OF THE SAND-PAPER
Coarse sand-paper (grain 50) removes in general the
bigger part of the material and fine sand-paper is used for
the finishing. If the surface is not even, then start with
rough sand-paper. Further you use middle coarse sand-
paper(grain 80) to remove the scratches left behind by
the coarse sand-paper and finally you take fine sand-
paper (grain 120) for the finishing.
REMOVING AND INSTALLING THE
SANDING BELT
Before assembly the sanding belt always remove
the plug from the mains.
• Put the machine on its side, with the drive belt cover
(10, Fig. A) down wards.
• Loosen the sanding belt fastener (7, Fig A).
• Remove the sanding belt from the machine
• Put a new sanding belt on the machine, make sure
that the direction arrows on the sanding belt are
pointing in the same direction as the direction
indicator (9, Fig. A).
• Fasten the sanding belt fastener again (7, Fig. A).
ALIGNING THE SANDING BELT
If the sanding belt doesn’t run parallel with the outer
edge of the housing, the sanding belt must be aligned.
Move the sanding belt in the correct position with the
adjusting knob (6, Fig. A). By turning the adjusting knob
clockwise the sanding belt will move to the inside and by
turning anti-clockwise the sanding belt will move to the
outside.
SWITCHING ON AND OFF
• To switch the machine on press the on/off switch (1,
Fig. A).
• To switch the machine off release the on/off switch
(1, Fig. A).
If continuous operation is required the blocking
switch (4 fig. A) must be used:
• Switch the machine on to press the on/off switch.
• Press the blocking switch (4, Fig. A) and release the
on/off switch.
• To switch the machine off press the on/off switch
again and release the on/off switch.
MOUNTING DUST BAG
Use the dust bag to collect dust which is released during
sanding.
• Put the dust bag on the dust collection opening (5,
Fig. A).
• Empty the dust bag regularly in order to obtain an
efficient dust extraction.
4Ferm
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BSM1005 - FBS-1000N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BSM1005 - FBS-1000N in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info