762274
7
Zoom out
Zoom in
Previous page
1/136
Next page
7
EN
Replacing cables or plugs
Immediately throw away old cables or plugs
when they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable
for the power input of the machine. The minimum
conductor size is 1.5 mm2. When using a cable
reel always unwind the reel completely.
3. ADJUSTING THE MACHINE
Adjusting the cutting depth
Fig.B
Move the motor housing (3) as far as possible
backwards.
Set the cutting depth by turning the cutting
depth adjustment knob (9).
The markings on the depth adjustment knob
(9) correspond to the biscuit dowel size being
used (16).
You can fine adjust the cutting depth setting by
turning the depth fine adjustment screw (10).
Move the motor base forwards and check if
depth fine adjustment screw (10) will fall in the
notch of the adjustment knob.
The following table shows the relationship of
the markings on the adjustment knob to cutting
depth, thickness of material and associated
biscuit dowel.
Marking Thickness Biscuit Cutting
of material Dowel depth in mm
0 8-12 mm No. 0 8.0
10 12-15 mm No. 10 10.0
20 > 15 mm No. 20 12.3
Max. - - 14.0
Adjusting the cutting angle
Fig. A + G
The cutting angle can be set the following way:
Release the angle adjustment knob (6) by
turning it anti-clockwise
The set angle is shown on the scale (21) below
the knob (6)
After setting to the right angle, tighten the
knob (6) again by turning it clockwise.
Adjusting the height to match material
thickness
Fig. B
The correct height can be set the following way:
Release the height adjustment knob (8) by
turning it anti-clockwise
The set height is shown by the scale and the
arrow (22).
After setting to the right height, tighten the
knob (8) again by turning it clockwise.
The height must correspond to half of the material
thickness of the working piece, the groove for the
biscuit dowel must always be in the middle of the
working piece.
4. MOUNTING ACCESSORIES
Prior to mounting an accessory always
unplug the tool.
How to change the saw blade
Your machine is delivered with the saw
blade already assembled on the machine
Fig. C & D
Put the machine in upside-down position and
remove the 4 screws on the bottom plate by
using a screw driver (not included)
Remove the bottom plate (20)
Press the spindle lock (5) and turn the spindle
until it engages in the lock. Keep the spindle
lock pressed during this procedure.
Remove the flange nut (17) from the spindle
by using the spanner (14) and turn it
counterclockwise.
Position the saw blade (18) on the flange (17).
Be aware that the arrow on the sawblade
indicates the same direction as the arrow on
the inside of the housing.
Place the flange nut (17) on the spindle and
tighten it with the wrench.
Take care the flange nut (17) will be placed the
correct way: The collar side must fit inside the
saw blade bore, the flat side must be pointing
upwards.
Release the spindle lock and check that the
spindle is unlocked by rotating it.
Assemble the bottom plate (20) again and fix
the 4 screws.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BJM1009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BJM1009 in the language / languages: All languages as an attachment in your email.

The manual is 12,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info