762274
6
Zoom out
Zoom in
Previous page
1/136
Next page
6
EN
- using the tool for different applications, or with
different or poorly maintainted accessories,
may significantly increase the exposure level
- the times when the tool is switched off or when
it is running but not actually doing the job, may
signifi cantly reduce the exposure level
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns.
2. SAFETY INSTRUCTIONS
Explanation of the symbols
Denotes risk of personal injury, loss of life
or damage to the tool in case of non-
observance of the instructions in this
manual.
Indicates electrical shock hazard.
Immediately unplug the plug from the
mains electricity in the case that the cord
gets damaged and during maintenance.
Keep bystanders away
Special safety instructions
Sawdust and splinters must not be removed
while the machine is running.
Do not use cutting discs or circular saw blades
in the machine.
Protect saw blades against shocks and
impacts.
Only use properly sharpened blades,
otherwise increased cutting forces will shatter
the work piece.
Before use, inspect the saw blade for any
damage. Do not use saw blades which are
cracked, ripped or otherwise damaged.
Make sure that the work piece is sufficiently
supported or clamped. Keep your hands away
from the surface to be cut.
Use the machine only with the auxiliary handle
When saw blades have to be mounted on
the thread of the spindle, make sure that the
spindle has sufficient thread.
Make sure that the saw blade has been
mounted and fastened properly. Do not use
reducing rings or adapters to make the saw
blade fit properly.
Apply the machine to the work piece only
when the machine is switched on.
When working with the machine always
hold the machine firmly with both hands and
provide for a secure stance.
Persons under 16 years of age are not
permitted to operate this machine.
Always wear safety goggles and hearing
protection. If desired or required also use
another protection for example an apron or
helmet.
Always disconnect the plug from the socket
before carry out any work on the machine.
Only plug-in when the machine is switched off.
Keep mains lead clear from working range
of the machine. Always lead the cable away
behind you.
Do not stop the blade by hand after switching
off.
The base plate must not be clamped down
while the blade is extended. Lowering and
raising the blade must be a smooth operation.
Always use the protective shields on the
machine.
Use only cutting discs whose allowable speed
is at least as high as the highest no-load speed
of the machine.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Your machine is double insulated in
accordance with EN 60745; therefore no
earthwire is required.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BJM1009 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BJM1009 in the language / languages: All languages as an attachment in your email.

The manual is 12,06 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info