Manual Ferm BJM1005 - FBJ-900P (page 8 of 54) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

763372

Zoom out

Zoom in

1/54

Ferm 101

• Tryk på tænd-sluk-knappen igen for at slukke maskinen, og knappen vil automatisk stille

sig på "sluk".

Brug aldrig spindellåsen til at slukke for motoren.

Markering af arbejdsemnerne

Fig. F

Før skyggefugefræseren tændes, skal arbejdsemnerne markeres på følgende måde.

• Anbring de to arbejdsemner, som skal forbindes, oven på hinanden.

• Fastgør arbejdsemnerne, og marker midten af fugespalten.

• Afstanden mellem to fugespalter bør være 10-15 cm. Dette gælder dog ikke for mindre

arbejdsemner, som ikke skal markeres.

Anbringelse af maskinen

Afhængig af arbejdsemnernes størrelse, kan maskinen anbringes på flere måder.

Større arbejdsemner

Fig. G

• Anbring maskinen tæt på arbejdsemnet.

• Midten af bundpladen (er markeret på bundpladen) skal vende mod midten af

arbejdsemnets fugespalte (se markering af arbejdsemnerne).

Mindre arbejdsemner

Fig. H

• Anbring maskinen tæt på arbejdsemnet.

• Maskinens side skal vende mod arbejdsemnets side.

Arbejdsemner smallere end 16 mm

Fig. I

• Anbring maskinen tæt på arbejdsemnet.

• Anbring justeringspladen (5) på vinkelstoppet (4).

• Sørg for, at skyggefugen til dyvlen er i midten af arbejdsemnet.

Hvis arbejdsemnerne er smallere end 16 mm, kan skyggefugen til dyvlen kun laves i midten af

arbejdsemnet ved brug af justeringspladen.

Savning af fugespalter

• Flyt motorhuset tilbage.

• Anbring maskinen tæt på arbejdsemnet.

• Anbring maskinen (se anbringelse af maskinen)

• Hold maskinen med begge hænder, og tænd den.

• Skub forsigtigt motorhuset så langt frem som muligt.

• Træk motorhuset tilbage, og sluk for maskinen.

Bevæg altid maskinen i den same retning som retningsrotationen. Se pilen øverst

på maskinen (16)

Ferm

Keep bystanders away

Faulty and/or discarded electrical or electronic apparatus have to be collected at

the appropriate recycling locations.

Special safety instructions

• Sawdust and splinters must not be removed while the machine is running.

• Do not use cutting discs or circular saw blades in the machine.

• Protect saw blades against shocks and impacts.

• Only use properly sharpened blades, otherwise increased cutting forces will shatter the

work piece.

• Before use, inspect the saw blade for any damage. Do not use saw blades which are

cracked, ripped or otherwise damaged.

• Make sure that the work piece is sufficiently supported or clamped. Keep your hands

away from the surface to be cut.

• Use the machine only with the auxiliary handle

• When saw blades have to be mounted on the thread of the spindle, make sure that the

spindle has sufficient thread.

• Make sure that the saw blade has been mounted and fastened properly. Do not use

reducing rings or adapters to make the saw blade fit properly.

• Apply the machine to the work piece only when the machine is switched on.

• When working with the machine always hold the machine firmly with both hands and

provide for a secure stance.

• Persons under 16 years of age are not permitted to operate this machine.

• Always wear safety goggles and hearing protection. If desired or required also use

another protection for example an apron or helmet.

• Always disconnect the plug from the socket before carry out any work on the machine.

Only plug-in when the machine is switched off.

• Keep mains lead clear from working range of the machine. Always lead the cable away

behind you.

• Do not stop the blade by hand after switching off.

• The base plate must not be clamped down while the blade is extended. Lowering and

raising the blade must be a smooth operation.

• Always use the protective shields on the machine.

• Use only cutting discs whose allowable speed is at least as high as the highest no-load

speed of the machine.

Electrical safety

When using electric machines always observe the safety regulations applicable in your

country to reduce the risk of fire, electric shock and personal injury. Read the following safety

instructions and also the enclosed safety instructions.

Always check that the power supply corresponds to the voltage on the rating plate.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BJM1005 - FBJ-900P in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4,74 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BJM1005 - FBJ-900P Manual

Product: