510089
7
Zoom out
Zoom in
Previous page
1/108
Next page
GB
7
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns


Denotes risk of personal injury, loss of
life or damage to the tool in case of non-
observance of the instructions in this
manual.
Indicates electrical shock hazard.
Immediately unplug the plug from the
mains electricity in the case that the
cord gets damaged and during
maintenance.
Keep bystanders away

• Sawdust and splinters must not be removed
while the machine is running.
• Do not use cutting discs or circular saw
blades in the machine.
• Protect saw blades against shocks and impacts.
• Only use properly sharpened blades,
otherwise increased cutting forces will shatter
the work piece.
• Before use, inspect the saw blade for any
damage. Do not use saw blades which are
cracked, ripped or otherwise damaged.
• Make sure that the work piece is sufficiently
supported or clamped. Keep your hands away
from the surface to be cut.
• Use the machine only with the auxiliary
handle
• When saw blades have to be mounted on the
thread of the spindle, make sure that the
spindle has sufficient thread.
• Make sure that the saw blade has been
mounted and fastened properly. Do not use
reducing rings or adapters to make the saw
blade fit properly.
• Apply the machine to the work piece only
when the machine is switched on.
• When working with the machine always hold
the machine firmly with both hands and
provide for a secure stance.
• Persons under 16 years of age are not
permitted to operate this machine.
• Always wear safety goggles and hearing
protection. If desired or required also use
another protection for example an apron or
helmet.
• Always disconnect the plug from the socket
before carry out any work on the machine.
Only plug-in when the machine is switched
off.
• Keep mains lead clear from working range of
the machine. Always lead the cable away
behind you.
• Do not stop the blade by hand after switching
off.
• The base plate must not be clamped down
while the blade is extended. Lowering and
raising the blade must be a smooth operation.
• Always use the protective shields on the
machine.
• Use only cutting discs whose allowable speed
is at least as high as the highest no-load
speed of the machine.

When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the power supply
corresponds to the voltage on the rating
plate.
Your machine is double insulated in
accordance with EN 60745; therefore
no earthwire is required.
Replacing cables or plugs
Immediately throw away old cables or plugs when
they have been replaced by new ones. It is
dangerous to insert the plug of a loose cable in
the wall outlet.
Using extension cables
Only use an approved extension cable suitable for
the power input of the machine. The minimum
conductor size is 1.5 mm
2
. When using a cable
reel always unwind the reel completely.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm BJM1001 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BJM1001 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info