Manual Ferm BGM1006 - FBSM 150-50N (page 6 of 50) (English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish)

632787

Zoom out

Zoom in

1/50

Ferm

Periodisk vedligholdelse på båndpudseren / slibemaskinen kan forhindre

unnødige problemer

• Hold ydersiden af båndpudseren/slibemaskinen ren, så alle bevægelige dele kan køre

uhindret og fri for slitage.

• Udskift slibeskiven og slibebåndet, når disse er slidte.

• Båndpudserens styrevalser kræver ikke smøring.

Fejl

For det tilfælde, at maskinen ikke fungerer korrekt, er herunder angivet en række mulige

årsager med tilhørende løsningsforslag:

Reparationer må udelukkende udføres af en autoriseret installatør eller et

autoriseret serviceværksted.

Rengøring

Rengør regelmæssigt maskinkappen med en blød klud, helst efter hvert brug. Sørg for at

ventilationshullerne er fri for støv og snavs.

Brug en blød klud, der er vædet i sæbevand til at fjerne hårdnakket snavs. Brug ingen

opløsningsmidler, så som benzin, alkohol, ammoniak, osv. Den slags stoffer beskadiger

kunststofdelene.

Smøring

Maskinen behøver ingen ekstra smøring.

Fejl

Skulle en fejl opstå, f.eks. pga. slidtage af en enhed, kontakt venligst serviceadressen på

garantibeviset. På bagsiden af denne manual finder du en tegning med alle dele, der kan

bestilles.

• Der er tændt for

maskinen, men den kører

ikke

• Den elektriske motor

bliver varm

• Der er en afbrydelse i

strømforsyningen til

maskinen

• Tænd/sluk-knappen er

beskadiget

• Motoren er defekt

• Kontrollér, om der er et

brud på netledningen

• Kontrollér afbryderne

eller sikringerne i

strømforsyningen

• Kontakt venligst

serviceadressen på

garantibeviset

• Kontakt venligst

serviceadressen på

garantibeviset

FIN

Ferm

• Is the belt grinder/linisher firmly mounted on a workbench?

• Because of the way it is used, the rotating parts of this belt grinder/linisher are not fully

covered. Therefore, take extreme care. Hold the workpiece firmly, so that it cannot fly out of

your hands and cause them to come into contact with the sanding belt or grinding wheel.

• The grinding wheel is a brittle part of this tool. The stone is not resistant to knocks.

Always grind on the front edge of the grinding wheel, and never on the side of the

grinding wheel. Never fit a cracked grinding wheel, as the high rotational speed could

cause the stone to fly apart, causing a serious accident.

• Always wear safety glasses when grinding or sanding.

• Never grind without using the eye shield.

• Avoid too much play between the tool rest and the grinding wheel or belt. With the

grinder, the play should be between 1 – 1.5 mm. The tool rest for the sanding belt

should be fixed such that the sanding belt can run freely.

• Only use the grinding wheel for the work it was designed for, for example, sharpening

tools. Do not use the grinding wheel for heavy construction work.

• Never ream out the hole in a grinding wheel to a larger diameter.

Whenever using the machine

In the interest of personal safety, only use accessories and auxiliary tools that

are recommended in the operator’s guide or in the catalogue. The use of other

than the mentioned accessories or auxiliary tools can lead to personal injury.

To avoid overheating, regularly allow the grinding machine to cool down. Use

the grinding machine for periods of no longer than 30 minutes.

• Check that the switch is NOT in the ON/’1’ position before connecting the machine to

the power supply.

• Always keep the power cord out of the way of the tool’s moving parts.

• Wear safety glasses.

• Wear a dust mask.

Immediately switch off the machine when:

• The machine overheats.

• The plug or power cord is defective or damaged.

• The switch is defective.

• You smell smoke or burning insulation.

Electrical safety

When using electric machines always observe the safety regulations applicable in your

country to reduce the risk of fire, electric shock and personal injury. Read the following

safety instructions and also the enclosed safety instructions.

Always check that the power supply corresponds to the voltage on the rating

plate.

FIN

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Ferm BGM1006 - FBSM 150-50N in the language / languages: English, German, Dutch, Danish, French, Italian, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Ferm BGM1006 - FBSM 150-50N Manual

Product: