762297

Ferm ATM1051 Manual

6
Zoom out
Zoom in
Previous page
1/48
Next page
6
EN
5. The jammed nail should then release.
If the jammed nail does not release, proceed as
follows.
6. With the magazine cover open, loosen the
three hexagonal headed screws (A).
Do not remove them!
Slide the striker cover forward and remove
from the front of the air nail gun.
7. Pull the jammed nail out with a pair of pliers or
similar tool, if necessary.
8. Replace the striker cover, slide it back and
tighten the hexagonal headed screws on the
front of the driver housing.
Checking operation of the air nailer
Remove all fasteners from the air nailer
before you perform a check.
• Hold the tool firmly by the handgrip, without
your finger on the trigger.
• Set the fastener head of the tool against the
work surface.
• Press the trigger so that the hammer pin
emerges. Release the trigger and the cycle is
complete.
Every time the trigger is pressed, the air
nailer will make a complete cycle.
6. MAINTENANCE
Whenever performing maintenance on
the air nailer, pay attention to the
warnings given in these instructions for
use, and be extra cautious when
troubleshooting problems with the air
nailer.
Replacing parts
Original parts are recommended when
replacement of parts is necessary. Do not use any
alternative parts that cannot perform as well as
the original parts in the appliance.
Please use Airline Lubricating Oil into the
air inlet on the handle of the Airnailer.
When there is no oil mist lubricator available,
add oil via the QD coupling once or twice a day,
while using. Just a few droplets of oil each time
is sufficient. Excessive oil will simply accumulate
in the appliance, which will become noticeable
when tacking.
Use during cold weather
With operation during cold weather, close to
or below freezing point, moisture in the air
pipeline can freeze, making use of the appliance
impossible. We recommend the use of a special
winter lubricant for pneumatic tools, or the
permanent use of antifreeze (glycol) as lubricant
when the temperatures are low.
Avoid storing the tool in a cold environment, to
prevent frost or ice formation on the operating
valves and mechanisms, which might cause
malfunction of the appliance.
Remark: Some commercial dehydrating fluids for
air pipelines are harmful to O-rings and
seals. Do not use these desiccants for
low temperatures without being certain of
compatibility.
ENVIRONMENT
To prevent damage in transit, the machine is
delivered in sturdy protective packaging. The
packaging is, as much as possible, made from
recycled materials. Therefore, take every possible
step to recycle the packaging.
WARRANTY
For the conditions of warranty, please refer to the
separately provided warranty card.
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm ATM1051 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm ATM1051 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info