762297
5
Zoom out
Zoom in
Previous page
1/48
Next page
5
EN
in the rate of wear. The air supply must be
sufficient to maintain the appliance’s working
pressure. Should the pressure diminish, the
driving power of the air nailer will be reduced. See
“TECHNICAL SPECIFICATIONS” for the correct
working pressure of the air nailer.
Oil and water separator
Dirt and water in the air supply are the main cause
of wear on pneumatic tools. An oil and water
separator will help to ensure clean air pressure
for the best performance and least wear on the
air nailer. The oil and water separator must be
regularly tapped off, in order to function effectively
in supplying clean air pressure to the tool.
Consult the manufacturer’s instructions for
the correct maintenance of the oil and water
separator. A contaminated and blocked filter
will cause a reduction in the pressure, which will
negatively influence the performance of the
air nailer.
4. LOADING
When in use, always wear eye protection
that meets the ANSI specifications, and
offers protection both in front and at the
sides from flying objects when loading,
operating and maintaining the air nailer.
Flying fasteners and splinters can cause
severe injury.
Remark: Glasses without side shield and face
protector do not offer sufficient protection.
Loading with fasteners
Fig.1
Disconnect the air hose.
Release the fastener latch and withdraw this
along the fastener guide unit (3).
Insert 1 fastener strip into the magazine.
Press the fastener guide unit back into the
magazine, and lock the fastener latch.
Reconnect the air hose to the air nailer.
5. OPERATING
When in use, always wear eye protection
that meets the ANSI specifications, and
offers protection both in front and at the
sides from flying objects when loading,
operating and maintaining the air nailer.
Flying fasteners and splinters can cause
severe injury.
Before using the air nailer
Read the general safety instructions and
warnings in these instructions for use carefully.
Refer to the specifications earlier in these
instructions for the correct operating
conditions for the air nailer.
Make sure the nailer is lubricated
properly before using it the first time.
Basic operation of the air nailer
Fig.1
A piston powered by compressed air drives the
air nailer.
Operating
Activated by a trigger (1)
Pressing the trigger activates the air nailer. Every
time the trigger is pressed, the air nailer will drive
a fastener into the workpiece.
This machine has an adjustable air outlet on top
of the machine (2).
Keep your hands well clear of the
fastener head. On no account should
you point the air nailer at any person or
animal.
Removing blocked nails
Before attempting to clear a jammed
nail, make sure that the air nail gun is
disconnected from the air supply.
To clear a jammed nail, proceed as follows.
1. Follow the compressor procedure to switch off
and release the air pressure.
2. Disconnect the air supply hose.
3. Press and hold the magazine release lever.
4. Slide the magazine cover back and remove the
nails in the magazine.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ferm ATM1051 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ferm ATM1051 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info