770286

Fenton 102.185 - RP180 Manual

4
Zoom out
Zoom in
Previous page
1/20
Next page
4
OVERVIEW
1. Lift Lever
Operate to lower or raise the tone-arm.
2. Autostop Switch ON/OFF
This switch turns auto stop on or off. When the
automatic stop is enabled, the platform will start
rotating as soon as the tone arm is placed over
the record and will stop rotating when it has
reached the end of the record. Some vinyl
records stop before the end or do not stop when
the end is reached. In this case set Auto-stop to
OFF.
3. 33 / 45 / 78 RPM Switch
This switch controls the RPM of the turntable
platter.
4. Cartridge with Needle
When the turntable is not in use, it is
recommendable to place the removable
protection cover on the stylus.
5. Platter
Place your record here.
6. BT LED
7. Power / Standby LED
8. Power / ON/OFF
Press to turn the device on/off.
9. Repeat
Press to select repeat single track (press once) or repeat full disc/folder (press twice).
10. Mode
Press to switch modes.
11. Previous
Press to play the previous track.
12. Play / Pause
Press to play or pause (depending on the current status).
13. Next
Press to play the next track.
14. Prog / Pair
Prog:
This function allows the CD tracks to be played in a programmed sequence.
NOTE: Program can only be set in STOP mode.
1. Load the CD Disc you wish to program.
2. Make sure the unit is in STOP mode by pressing the STOP button.
3. Press the program / pair button once, the LED display will flash "00" on the LED display.
4. Press previous- or next button until the desired track number is reached.
5. Press the program / pair button again to store the selection.
6. Repeat the (4) to (5) steps until you have entered all the tracks you want to program.
7. To play the stored sequence, press the play / pause button.
8. After all the stored tracks have been played the CD will automatically stop.
Pair:
Press and hold for 3 seconds to disconnect BT.
15. Open / Close
Press to open/close the CD drawer.
16. Stop
Press to stop play.
17. Volume Control
Turn to adjust the master volume.
18. DC IN port
Connecting the 12Volt/DC power adapter.
19. RCA Line output
The audio from a playing vinyl record is sent to this line-level coaxial audio output. This must not be connected to phono
level devices.
20. AUX input
3.5mm(1/8) jack connector for auxiliary input.
21. FM Antenna
22. CD Drawer
23. Dial Knob
24. Dial Scale
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fenton 102.185 - RP180 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fenton 102.185 - RP180 in the language / languages: English, German, Dutch, French, Spanish as an attachment in your email.

The manual is 0.63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info