Manual Fendt Opal 2021 (page 70 of 123) (English)

814626

Zoom out

Zoom in

1/123

7. Installation of electrical devices

• Only accumulator batteries with bound electrolytes

(gel or AGM batteries) may be installed in those po-

sitions specied by the manufacturer.

• The installed battery may not be opened.

• When changing auxiliary batteries, use only batteries

of the same make and capacity.

• Before disconnecting or connecting the auxiliary bat-

tery, disconnect the electric connection to the base

vehicle and switch o the 230 V supply, the

12 V supply as well as all electrical devices.

• Before replacing fuses you must rst de-energise

the charge controller.

• Before replacing a blown fuse you must rst x

whatever caused the fuse to blow.

• Fuses may only be replaced by fuses with the same

fuse protection value.

• Airing the charge controller insuciently will cause a

reduction of the charge current.

• The surface of the charge controller casing may be-

come hot when the device is in operation.

• Before each journey, please check that the battery is

charged. Where necessary, set up a mains connection

so that the battery can be charged.

• Use every opportunity during your journey to charge the

battery.

• The battery loses its capacity after having been used for

a while and at low temperatures.

• An acoustic warning signal will be given o if the remai-

ning time during discharge operation is less than 1 hour.

• If the battery voltage should be less than 10.0 V, all de-

vices will automatically be switched o.

• A warning will go o if the battery ages to a value less

than 50% of its nominal capacity.

• If the vehicle is not in use for a longer period of time,

the battery should be disconnected or the main switch

should be switched o after the battery has been opti-

mally charged.

SiA

A4 A3

SiB

DauerPlus

Plus

SiC

C3 C1

SiD

D2B

D3B

D1Plus

D2Plus D2Plus

D3a

SiF

SiE

E2B

E3B

E2Plus

E1Plus E2Plus

E3a

S40 S39 S38

S34

S35

S36

S41

++--

-S37

Hauptpanel

Funkmodul

Schlafraum

Außenbel.

CI-

BUS CI-

BUS

CI-

BUS CI-

BUS

CI-

BUS CI-

BUS WLAN Gas

1 2

Battery

sensor

connection

Jumper

• A warning will go o if the battery ages to a value

less than 50% of its nominal capacity.

• If the vehicle is not in use for a longer period of time,

the battery should be disconnected or the main

switch should be switched o after the battery has

been optimally charged.

The “Jumper”

setting must also be changed if an inde-

pendent system and a battery are installed in the camper

at a later stage. In self-sucient mode, the bridge circuit

must be connected to the two pins in such a way that both

of them are electrically connected. When this conversion

has been carried out, it is possible to switch all devices on

during battery operation.

Orderly functioning of the described displays on the TFT

display can only be achieved in conjunction with an intelli-

gent battery sensor (IBS) connected to the circuit board

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fendt Opal 2021 in the language / languages: English as an attachment in your email.

The manual is 4.12 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Fendt Opal 2021

Fendt Opal 2021 User Manual - German - 123 pages

Fendt Opal 2021 User Manual - Dutch - 123 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fendt Opal 2021 Manual

Product: