443086
5
Zoom out
Zoom in
Previous page
1/16
Next page
5
1. LINE CORD - Connect the power line cord to a
grounded AC receptacle in accordance with the volt-
age and frequency ratings as listed on the rear panel of
the amplifier.
2. 8 OHM SPEAKER JACK (Combo & Head models) -
Plug-in connection for external 8 ohm speakers only.
3. 4-OHM ADDITIONAL SPEAKER JACK (Head model
only) - Plug-in connection for a external 4 ohm speaker
or a second 8 Ohm speaker enclosure. The combined
minimum impedance for all speaker enclosures should
be 4 ohms (i.e. two 8 ohm enclosures in parallel).
4. LINE OUT - This jack provides a signal output suitable
for connection to recording and sound reinforcement
equipment. Using a 3-conductor stereo cord will pro-
vide a quasi-balanced signal and a 2-conductor mono
cord will provide an unbalanced signal.
5. SEND - Connect cord to external equipment at this
output jack. This unbalanced jack provides a pre-
reverb signal output from the preamp and may be used
to drive effects units in an effects loop, to drive addi-
tional amplifiers in a multi-amp set up or as a preamp
send to a mixing console.
6. LEVEL SWITCH - This switch directly effects the SEND
jack (item 5) by boosting or attenuating the signal sent
to the effects. External rack effects usually require
–7dB or +4dB settings. Effects pedals usually require
a –16dB setting.
7. RETURN - Connect cord from external effects devices
at this input jack. Inserting a plug at this jack auto-
matically disconnects the unit’s internal connection
from the pre-amp to the power amp. This jack is pre-
reverb and can also be used as a power amp input.
Plugging into this jack activates the EFFECTS MIX
control on the front panel.
R
R
e
e
a
a
r
r
P
P
a
a
n
n
e
e
l
l
F
F
u
u
n
n
c
c
t
t
i
i
o
o
n
n
s
s
S
S
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
1
2 3
4 5 6
7
TYPE: PR 209
PART NUMBERS: (Combo) (Head)
22-6808-000 (120V, 60 Hz)USA; 22-6868-000 (230V, 50 Hz)Euro; 22-6807-000 (120V, 60 Hz)USA; 22-6867-000 (230V, 50 Hz)Euro;
22-6838-000 (240V, 50 Hz)Aust; 22-6878-000 (100V, 50/60 Hz)Jpn 22-6837-000 (240V, 50 Hz)Aust; 22-6877-000 (100V, 50/60 Hz)Jpn
POWER REQUIREMENTS: 300W
INPUT IMPEDANCE: > 1 M
NOMINAL LEVEL: 100mV
POWER OUTPUT: 69W into 8 at 5% THD 94W into 4 at 5% THD
EFFECTS LOOP: NOMINAL LEVEL: Selectable +4, -7, -16 dBv
OUTPUT IMPEDANCE: 1.2 k max.
INPUT IMPEDANCE: 100k
TUBE COMPLEMENT: One 12AX7A (ECC83) (P/N 013341)
SPEAKER (Combo only): 8, 12” Fender Special Design (P/N 040598)
EXTERNAL SPEAKER: (Combo) Fender recommends Guitar enclosure GE-112 Mk II (P/N 21-1660-010) @ 8
(Head) Fender recommends Guitar enclosure GE-412 Mk II (P/N 21-1662-010) @ 4
FOOTSWITCH (Included): 3 button: Gain, Gain Select and Reverb
DIMENSIONS: (Combo) (Head)
HEIGHT: 17.5 in. (44.5 cm) 8.5 in. (21.6 cm)
WIDTH: 22.5 in. (56.8 cm) 22.5 in. (56.8 cm)
DEPTH: 10.25 in. (25.9 cm) 9.5 in. (24.1 cm)
WEIGHT: 41 lbs. (18.6 kg) 25 lbs. (11.4 kg)
Product specifications are subject to change without notice.
TUBE REPLACEMENT: Roc Pro amplifiers utilize one Fender Special Design 12AX7A vacuum tube. It’s a good idea to keep a spare
tube with the amplifier in case the tube in the Roc Pro should fail and as a test for tube wear. Loss of sound quality due to the tube
reaching the end of its life is very gradual and may not be noticed. Replacing the old tube with your spare and listening for improvement
will tell if the old tube is worn and whether you should replace it and buy a new spare! Replace only with the identical tube type.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fender Roc Pro 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fender Roc Pro 1000 in the language / languages: English as an attachment in your email.

The manual is 3,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info