502511

Felisatti NTF250 Manual

7
Zoom out
Zoom in
Previous page
1/52
Next page
Model NTF250/1200ST NTF305/1600ST
Tension and current V / A 230V-5,5A 230V-8A
Frequency Hz 50 50
Absorbed power W 1200 1600
Idling speed /min 4500 4000
Cut at 90°/crop (AxB g. 3) mm 73x150 102x150
Cut at 45°/crop (AxB g. 4) mm 73x90 97x102
Cut at 45°/blade at 45° (AxB g. 6) mm 46x150 66x150
Cut at 45°/blade at 45° (AxB g. 6) mm 45x48 45x53
Cut on upper table mm 40 66
Upper table dimensions mm 473x312 473x312
Blade diameter mm 250 305
Blade hole diameter mm 30 30
Weight kg 22 25
Overall dimensions (LxHxW) mm 520x396x650 573x432x667
Sound pressure emitted Lpa dB(A).(*) 91 96
Sound power emitted Lwa dB(A).(*) 104 109
Vibration level m/s2 (*) 1,0 (<2,5) 0,7 (<2,5)
* Reliefes enforced by the standard: EN 61029
2.2 STANDARD ACCESSORIES
This series of mitre saws is supplied complete with
the following set of standard accessories:
Adjusting rod (g. 7): required for the cutting of beams
of the same length.
Pusher For the working of small parts on the upper
table (g. 20).
Blister pack of Allen wrenches.
Important: the equipment provided may vary
according to the sales campaign in progress.
2.3 ACCESSORIES AVAILABLE ON REQUEST
The following accessories for particular work
conditions are also available on request:
Rapid clamp: (g. 8) permits the tighter locking of
bars and sections without vibration.
Foldable and movable universal support for mitre
saws (A g. 19).
Support and roller unit (B g. 19) for jutting piece
Vacuum unit (C g. 19) with connection tube and
spout.
Goniometer: to make angled cuts on the upper
table
(g. 21).
Workpiece support stroke-end raised section (G
g.1
WARNING! The use of accessories or attachments
other than those recommended in this manual may
pose risk of injury.
2.4 SAFETY DEVICES
In rest position, the blade is completely protected
by two xed casings and one movable casing with
opening that is automatically triggered by the lowering
of the blade unit during the execution of the cut.
On the upper table, the blade is protected by a casing
that is raised over the workpiece as it approaches the
cutting point.
WARNING! Never remove these protective casings
that enable the operator to work in conditions of
safety.
WARNING!
CHECK ALL DAMAGED PARTS
• All the parts of the tool should be carefully checked
before use in order to make sure that they will work
correctly for the operation foreseen.
• Check the alignment and assembly of all moving
parts for signs of breakage and any other conditions
that might compromise operation.
• Damaged protective casings and/or other parts
should be replaced by an authorised service center
unless indicated otherwise in this manual.
• Have defective switches replaced by an authorised
service center.
If the LOCK in “ON” button has not been pressed,
the blade automatically stops when the starting
lever switch in the handgrip is released.
WARNING!
Pressing the LOCK in “ON” button disables the safety
feature provided by the Manufacturer in the starting
2.1 TECHNICAL DATA
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Felisatti NTF250 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Felisatti NTF250 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info