502238

Fein MSh636-1 Manual

18
Zoom out
Zoom in
Previous page
1/82
Next page
18
en
Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces. Always
use auxiliary handle, if provided, for maximum control over
kickback or torque reaction during start-up.
The operator
can control torque reactions or kickback forces, if proper
precautions are taken.
Never place your hand near the rotating accessory.
Acces-
sory may kickback over your hand.
Do not position your body in the area where power tool will
move if kickback occurs.
Kickback will propel the tool in
direction opposite to the wheel’s movement at the point
of snagging.
Use special care when working corners, sharp edges, etc.
Avoid bouncing and snagging the accessory.
Corners,
sharp edges or bouncing have a tendency to snag the
rotating accessory and cause loss of control or kickback.
Do not attach a saw chain woodcarving blade or toothed
saw blade.
Such blades create frequent kickback and loss
of control over the power tool.
Special safety warnings for grinding
Use only wheel types that are recommended for your power
tool and the specific guard designed for the selected wheel.
Wheels for which the power tool was not designed can-
not be adequately guarded and are unsafe.
Wheels must be used only for recommended applications.
For example: do not grind with the side of cut-off wheel.
Abrasive cut-off wheels are intended for peripheral
grinding, side forces applied to these wheels may cause
them to shatter.
Always use undamaged wheel flanges that are of correct
size and shape for your selected wheel.
Proper wheel
flanges support the wheel thus reducing the possibility of
wheel breakage. Flanges for cut-off wheels may be differ-
ent from grinding wheel flanges.
Do not use worn down wheels from larger power tools.
Wheels intended for larger power tools are not suitable
for the higher speed of a smaller tool and may burst.
Additional safety warnings
Use elastic spacers/liners when these are provided with the
grinding/sanding accessory.
Make sure that the application tools are mounted in accord-
ance with the manufacturers instructions. The mounted
application tools must be able to rotate freely.
Incorrectly
mounted application tools can become loose during
operation and be thrown from the machine.
Handle accessories carefully and store them according to
the manufacturer’s instructions.
Damaged accessories can
form cracks and break off during operation.
When using application tools with a threaded insert, take
care that the thread in the application tool is long enough
to hold the spindle length of the power tool. The thread in
the application tool must match the thread on the spindle.
Incorrectly mounted application tools can loosen during
operation and cause injuries.
Do not machine any material containing asbestos.
Asbestos
is cancerogenic.
Beware of any concealed electric cables, gas or water con-
duits;
check the working area with a metal detector, for
example, before commencing work.
Use a stationary extraction system, blow out ventilation
slots frequently and connect a residual current device
(RCD) on the line side.
When working metal under
extreme operating conditions, it is possible for conduc-
tive dust to settle in the interior of the power tool. The
total insulation of the power tool can be impaired.
Do not rivet or screw any name-plates or signs onto the
power tool.
If the insulation is damaged, protection against
an electric shock will be ineffective. Adhesive labels are
recommended.
MSh635:
Always work using the auxiliary handle.
The aux-
iliary handle ensures reliable guidance of the power tool.
Before putting into operation, check the mains connection
and the mains plug for damage.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
The vibrational emission values are given for dry grinding
of metal with grinding points. Other applications, such as
shaping with hard metal cutters, can lead to other vibra-
tional emission values.
Operating instructions.
Use the respective collet chuck to fit the grinding wheel.
Insert the shaft of the grinding wheel into the collet chuck
as far as the stop.
Note:
Observe the maximum permitted projecting shaft
length (a) of the grinding accessory according to the man-
ufacturer’s instructions. (see page 10)
Using the same pressure, move the power tool back-
wards and forwards across the surface of the work piece
to prevent it from becoming too hot.
Repair and customer service.
Blow out the interior of the power tool at
regular intervals from outside through the air
vents with dry, compressed air.
If the supply cord of this power tool is damaged it must
be replaced by a specially prepared cord available
through the FEIN customer service centre.
If required, you can change the following parts yourself:
Application tools, Auxiliary handle (MSh635), Collet.
3 41 00 324 06 9 - GB Seite 18 Mittwoch, 29. Oktober 2008 1:50 13
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fein MSh636-1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fein MSh636-1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info