Manual Fein MSh636-1 (page 17 of 82) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

502238

Zoom out

Zoom in

1/82

For your safety.

Read all safety warnings and all instruc-

tions.

Failure to follow the warnings

and instructions may result in electric

shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

Do not use this power tool before you have thor-

oughly read and completely understood this

Instruction Manual and the enclosed “General

Safety Instructions” (document number

3 41 30 054 06 1). The documents mentioned should be

kept for later use and enclosed with the power tool,

should it be passed on or sold.

Please also observe the relevant national industrial safety

regulations.

Intended use of the power tool:

Hand-guided straight grinder for commercial use, for dry

grinding of metal with grinding points in weather-pro-

tected environments using the application tools and

accessories recommended by FEIN.

MSh636-1: The straight grinder is also intended for shap-

ing metal with hard metal cutters.

Safety warnings common for sanding, sanding with

sanding sheets, working with wire brushes,

polishing and cut-off grinding

This power tool is to be used as a grinder. Observe all safety

warnings, instructions, illustrations and data supplied with

the power tool.

Non-observance of the following instruc-

tions can lead to electric shock, fire and/or serious injury.

This power tool is not suitable for sanding with sanding

sheets, working with wire brushes, polishing and cut-off

grinding.

Applications, for which the power tool is not

intended for, can lead to hazardous situations and injury.

Do not use accessories which are not specifically designed

and recommended by the tool manufacturer.

Just because

the accessory can be attached to your power tool, it does

not assure safe operation.

The rated speed of the accessory must be at least equal to

the maximum speed marked on the power tool.

Accessories

running faster than their rated speed can break and fly

apart.

The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately

guarded or controlled.

The arbor size of wheels, flanges, backing pads or any other

accessory must properly fit the spindle of the power tool.

Accessories with arbor holes that do not match the

mounting hardware of the power tool will run out of bal-

ance, vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use inspect

the accessory such as abrasive wheels for chips and

cracks, backing pad for cracks, tear or excess wear, wire

brush for loose or cracked wires. If power tool or accessory

is dropped, inspect for damage or install an undamaged

accessory. After inspecting and installing an accessory,

position yourself and bystanders away from the plane of the

rotating accessory and run the power tool at maximum no-

load speed for one minute.

Damaged accessories will nor-

mally break apart during this test time.

Wear personal protective equipment. Depending on appli-

cation, use face shield, safety goggles or safety glasses. As

appropriate, wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping small abrasive or

workpiece fragments.

The eye protection must be capable

of stopping flying debris generated by various operations.

The dust mask or respirator must be capable of filtrating

particles generated by your operation. Prolonged expo-

sure to high intensity noise may cause hearing loss.

Keep bystanders a safe distance away from work area. Any-

one entering the work area must wear personal protective

equipment.

Fragments of workpiece or of a broken acces-

sory may fly away and cause injury beyond immediate

area of operation.

Hold power tool by insulated gripping surfaces only, when

performing an operation where the cutting accessory may

contact hidden wiring or its own cord.

Cutting accessory

contacting a “live” wire may make exposed metal parts of

the power tool “live” and shock the operator.

Position the cord clear of the spinning accessory.

If you

lose control of the power tool, the cord may be cut or

snagged and your hand or arm may be pulled into the

spinning accessory.

Never lay the power tool down until the accessory has come

to a complete stop.

The spinning accessory may grab the

surface and pull the power tool out of your control.

Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

Regularly clean the power tool’s air vents.

The motor’s fan

will draw the dust inside the housing and excessive accu-

mulation of powdered metal may cause electrical haz-

ards.

Do not operate the power tool near flammable materials.

Sparks could ignite these materials.

Do not use accessories that require liquid coolants.

Using

water or other liquid coolants may result in electrocution

or shock.

Kickback and related warnings

Kickback is a sudden reaction to a pinched or snagged

rotating wheel, backing pad, brush or any other acces-

sory. Pinching or snagging causes rapid stalling of the

rotating accessory which in turn causes the uncontrolled

power tool to be forced in the direction opposite of the

accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched

by the workpiece, the edge of the wheel that is entering

into the pinch point can dig into the surface of the mate-

rial causing the wheel to climb out or kick out. The wheel

may either jump toward or away from the operator,

depending on direction of the wheel’s movement at the

point of pinching. Abrasive wheels may also break under

these conditions.

Kickback is the result of power tool misuse and/or incor-

rect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

WARNING

3 41 00 324 06 9.book Seite 17 Mittwoch, 29. Oktober 2008 1:20 13

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fein MSh636-1 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 3,81 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fein MSh636-1 Manual

Product: