784930

Fantasy Entice Manual

13
Zoom out
Zoom in
Previous page
1/24
Next page
For further inquiries, please contact our Customer Service Team
Email: ahsservice@watkinsmfg.com Phone: +1 760 598 6464 10
CONTROL PANEL OPERATION
INITIAL START-U
P - When the spa is
first powered up the control system begins a 2
minute Startup Mode. Different codes will display
on the screen. Once Startup
Mode completes,
the actual temperature is displayed on the
screen, and the spa will then begin to heat and
maintain the water temperature and the first filter
cycle will start. Your spa has been designed so
that it will automatically heat the water to the
factory set temperature of 38°C (100°F) unless
you set the spa to a different temperature.
If power is disconnected from the spa, it will
automatically revert back to the last saved set
temperature when power is reapplied.
ADJUST TEMPERATURE
The temperature can only function between
26.5°C - 40°C (80°F - 104°F). The last measured
temperature will constantly display on LCD.
Press the Plus or Minus buttons to display the set
temperature and indicator . Each time either
button is pressed again, the set temperature
will increase or decrease depending on which
button is pressed. After five seconds, the LCD will
automatically display the current spa temperature.
The “heater” indicator lights up when the
heater is on. It flashes when there is a request
for more heat, but the heater is not on. Once set
temperature is reached the indicator shuts off
and the low speed of the jet pump turns off after
30 seconds (if not in filter cycle).
JETS OPERATION
Firmly press the Jets button once to activate the
low speed of the pump and again for the high
speed. Firmly press the Jets button again to turn
off the pump
(unless spa is heating or in a filter
cycle).
If left running the low or high speed pump
will automatically turn off after 1 hour. The "Jets"
indicator light next to the button will blink when jet
pump is on low speed and is solid on high speed.
MULTI COLOR LED LIGHT
Press the Light button once to turn on the light,
the light indicator next to the button is lit when the
light is on. Press the button again to turn the light
off. Every time the light is quickly turned off and
on a new light mode will appear. The sequence is
as follows: White, Aqua, Magenta, Azure, Amber,
Emerald, Ruby, color wheel with abrupt color
changes, slow full color wheel and fast full color
wheel. The last light mode used will come back
on when the light is turned off for more than 2
seconds.
NOTE: If left on, the light will automatically turn off
after 4 hours of operation.
FILTER CYCLES
There are two filter cycles: the first cycle (F1)
starts right after power up and the second cycle
(F2) will start 12 hours later. The default duration
for the first filter cycle is 1 hour, and 30 minutes
for the second cycle. Filter cycles only run at low
speed. The “Filter” indicator lights up when a
filter cycle is on. The duration of each filter cycle
can be modified.
ADJUSTING PRESET FILTER
CYCLES
Filter duration is programmable between 0 and 6
hours in 30 minute increments (0.5 hours) for both
filter cycles. To program the cycle times:
1. Press and hold Mode button for 5 seconds
until F1 is displayed.
2. Press the Plus or Minus button to adjust
the cycle time for F1.
Jets
Indicator Lights
Temp Minus
Temp Plus
Light Mode
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Fantasy Entice at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Fantasy Entice in the language / languages: English as an attachment in your email.

The manual is 0.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info