698465
21
Zoom out
Zoom in
Previous page
1/80
Next page
21
ENGLISH
.
Fan failure Fan or control
electronic is
defect
Replace the module
.
Defect ive tempe-
rature probe on
inductor
Sensor signal
out of valid
range; sensor
or electronic is
defect
Replace the module
.
Hardware defect
of induction
module
Defect har-
dware device
detected by the
self-check of the
module
Replace the module
.
Conguration
failure
2 cooking zones
are delicated to
the same ele-
ment of the UI
Delete the actual
conguration
manual congura-
tion with service
menu
.
Fixed sensor va-
lue (test function
for T probe on
inductor)
Not enough
temperature
change (10 K)
within 5 min
after switch on
the hob
System must cool
down
No fun-
ctionality
and no
displaying
Overvoltage on
the switch mode
power supply (no
functionality)
400 V con-
nection
Disconnect and
correct the power
line connection
Note:
Not each failure can be delected automatically by the system, e.g. in case of
defect of the User interface power supply.
COOKER HOOD
FUMES DISCHARGE
EXTERNAL EXHAUST HOOD SUCTION
In this version the fumes and vapours are discharged outside
through the exhaust pipe.
To this end, the hood outlet tting must be connected via a
pipe, to an external output.
The outlet pipe must have:
a diameter not less than that of the hood tting.
a slight slope downwards (drop) in the horizontal sections to prevent con-
densation from owing back into the motor.
the minimum required number of bends.
the minimum required length to avoid vibrations and reduce the suction
performance of the hood.
You are required to insulate the pipes if it passes through cold environ-
ments.
In the presence of motors with 800m
3
/h or higher, a check valve is present
to prevent external air owing back.
Deviation for Germany:
when the kitchen hood is used at the same time as appliances that are powered by
energy other than electricity, the negative pressure in the room must not exceed 4 Pa
(4 x 10-5 bar).
HOOD WITH INTERNAL RECIRCULATION FILTERING
In this model, the air passes through the charcoal lters (op-
tionale) to be puried and recycled in the environment.
ASSEMBLY INSTRUCTIONS
only intended for qualied personnel
The hood can be installed in various congurations.
The generic assembly steps apply to all installations; for each case,
follow the specic steps provided for the required installation.
OPERATION
TOUCH PUSHBUTTON PANEL
ON/OFF
Short pulse: Hood switch ON/OFF
Long pulse: Hood operation automatic cycle activation (A) accor-
ding to plate
power.
Speed increase from 1 to…9 (up to “P”).
Speed “P”: active only for a few minutes, then speed 9.
Speed decrease from P to 1.
With hood active (short pulse): TIMER (ashing red LED)
Automatic switch-o after 15 min.
The function is disabled (red LED OFF) if:
- The motor is switched o (button
).
- Press the TIMER button
again .
With the hood OFF (long pulse 4s):
opening the ns for hood and metal lter maintenance
FAT METAL FILTER ALARM
Maintenance after about 30 hours’ use.
Press button
for 5 seconds to reset the counter.
CARBON.ZEO FILTER ALARM
Maintenance after about 2000 hours’ use.
Press button for 5 seconds to reset the counter.
To activate the alarm:
With the hood OFF, press the buttons and for 3 se-
conds.
The LED
lights up.
Conrm with button
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falmec Quantum at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falmec Quantum in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Falmec Quantum

Falmec Quantum User Manual - Dutch - 72 pages

Falmec Quantum Additional guide - All languages - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info