• With external exhaust (suction) versions, it is possible to insert extension (H) with the slots facing downwards so that they are not visible when
the installation height allows it.
Phase
F page 6
• Slide the extension (H) until it is positioned at the desired height (Fig.
1
).
• Following what is indicated in Fig.
2
, draw a line on the wall that will be used to position the bracket (L) correctly.
• Place the bracket (L) on the wall by following the line drawn on it. With a spirit level, check the horizontal alignment and mark the 2 drilling points
at the ends (Fig.
3
).
• Drill the holes, insert 2 expansion plugs (ø 6mm) and fasten the bracket (L) with the relative screws (V4) (Fig.
4
).
• Tighten the extension (H) to the bracket (L) using screws (V5) (Fig.
5
).
• Electrically power the hood in accordance with regulations in force.
OPERATION
WHEN SHOULD THE HOOD BE SWITCHED ON AND OFF?
Switch on the hood at least one minute before starting to cook: this enhances the airflow to convey fumes and vapours towards the suction surface.
After cooking, leave the hood operating until complete extraction of all vapours and odours. If required, by means of the Timer function, it is possible
to set hood auto switch-off after 15 minutes of operation.
WHICH SPEED IS TO BE SELECTED?
The rst speed is a low consumption energy-saving way of keeping the air clean, the second speed is used in normal conditions, and the third
speed is used when there are strong odours and vapours.
WHEN SHOULD THE FILTERS BE WASHED OR REPLACED?
The hood is assembled with two different types of filters: metal ones (washable) and active carbon ones (non-washable). The former must be
cleaned every 30 hours of use (the fixed red light
indicates that they need to be washed), the latter are to be replaced every 3-4 months, de-
pending on the use of the hood. For further information, please read the chapter regarding "Maintenance" on page 19.
USE OF ELECTRONIC PUSH BUTTON CONTROL PANEL
Timer/Filters alarm
Pressing the key with the motor active at any speed activates
the Timer function: this function determines the auto switch-
o of the hood after 15 minutes of operation. Activation of
the function is signalled by a RED ashing light.
With the Timer function active, the hood can still be switched
off by the user at any time by pressing the key
: the function
will be automatically disabled and the RED light will turn off.
Should the speed be changed with the Timer function active,
the latter will be automatically disabled.
On the other hand, ignition of the xed RED light indicates a
grease lter alarm: this alarm notifies that it is time to wash
the metal anti-grease filters (the alarm is triggered after approx-
imately 30 hours of use). After cleaning the filters, disable the
alarm and reset the counters by keeping the key pressed for 3
seconds.
To disassemble and assemble the anti-grease metal filters,
refer to the instructions on drawing
G on page 7.
Mode button (ON/OFF)
Pressing the key switches on (or off) the hood motor: it starts at
the previously selected speed prior to switching it off (desired
speed function). Should you wish to use a different speed, set
if by using the + and - keys.
Button +
By pressing the key, the motor speed increases. Speeds 1, 2 and
3 are displayed by the number of LEDs switched on, excluding
the light and timer LEDs.
The + key in the version with 4 speeds has an intermittent light:
the 4th speed or intensity is timed and after approximately 7
minutes the motor automatically switches to 3rd speed.
Button -
By pressing the key, the motor speed reduces. Speeds 1, 2 and
3 are displayed by the number of LEDs switched on, excluding
the light and timer LEDs.
Light button
ON: light on (lit button) OFF: light off
LIGHTING
The range hood is equipped with high efficiency, low consumption LED spotlights with extremely long duration under
normal use conditions.
Should the LED spotlight need to be replaced, proceed as shown in the figure
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Falmec Onda at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Falmec Onda in the language / languages: All languages as an attachment in your email.
The manual is 14,77 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
