Manual Falmec Atlas Vetro Wall (page 16 of 84) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

662001

Zoom out

Zoom in

1/84

USE AND CLEANING WARNINGS

•Before cleaning or carrying out maintenance operations, disconnect the equipment by removing the plug or switching o the main

switch.

•Do not use the hood with wet hands or bare feet.

•Always check that all electrical parts (lights, extractor fan) are oﬀ when the equipment is not used.

•The maximum overall weight of any objects placed or hung (if applicable) on the hood must not exceed 1.5 Kg.

•Check the deep-fryers during use: Overheated oil can catch ﬁre.

•Do not light naked ﬂames under the hood.

•Do not ﬂambé foods under the hood.

•Never use the hood without the metal anti-grease ﬁlters: in this case, grease and dirt will deposit in the equipment and compromise its operation.

•Accessible parts of the hood can be hot if used together with cooking appliances.

•Do not carry out any cleaning operations when parts of the hood are still hot.

•There can be a risk of ﬁre if cleaning is not carried out according to the methods and products indicated in this booklet.

•Disconnect the main switch when the equipment is not used for long periods of time.

If other appliances that use gas or other fuels are being used at the same time (boiler, stove, ﬁreplaces, etc.), make sure the room where the

fumes are extracted is well-ventilated, in compliance with the current regulations.

WARNINGS IN CASE OF MALFUNCTION

•DO NOT use the hood if the power supply cable or other components are damaged. Disconnect the hood from the electrical power supply

and contact the Dealer or an authorised Servicing Department for repairs. Insist on original spare parts. Do not personally try to carry out re-

pairs or replacements. Interventions carried out by incompetent and unauthorised persons can cause damage, even serious, to things

and/or persons not covered by the Manufacturer's warranty.

The Manufacturer reserves the right to make changes to the equipment at any time and without prior notice. Printing, translation and reproduction,

even partial, of this manual are bound by the Manufacturer's authorisation.

Technical information, graphic representations and speciﬁcations in this manual are for information purposes and cannot be divulged.

This manual is written in Italian. The Manufacturer is not responsible for any transcription or translation errors.

INSTALLATION (only intended for personnel qualied to install the hood)

Before installing the hood, carefully read Chap. "Safety instructions and warnings" on page 15.

TECHNICAL FEATURES

The technical speciﬁcations are reported on the identiﬁcation plate located inside the hood.

POSITIONING

The minimum distance between the highest part of the equipment for cooking and the lowest part of the hood is indicated in Fig. A on

page 5.

Generally, when the hood is placed on gas cookers, this distance must be at least 65 cm (25.6"). However, according to an interpretation of standard

EN60335-2-31 dated 11-07-2002 of TC61 (sub-clause 7.12.1 meeting 15 agenda item 10.11), the minimum distance between the cooker and lower

part of the hood can be reduced to the reported quota.

Should the instructions for the gas cooker specify a greater distance, take this into consideration.

Do not install the hood outdoors and do not expose it to atmospheric agents (rain, wind, etc.).

ELECTRICAL CONNECTION (only intended for personnel qualied to install the hood)

Disconnect the equipment from electrical mains power supply before carrying out any operations on the hood.

Make sure that the wires inside the hood are not disconnected or cut. Should this occur, contact your nearest Servicing Depart-

ment. Refer to qualied personnel for electrical connections.

Connection must be carried out in compliance with the provisions of law in force.

Before connecting the equipment to the electrical mains power supply, check that:

•voltage supply corresponds with what is reported on the identiﬁcation plate located inside the hood;

•the electrical system is compliant and can withstand the load of the equipment (refer to the technical speciﬁcations on the identiﬁcation plate

located inside the hood);

•once connected, the plug and cable do not come into contact with hot parts having temperatures that exceed 70°C;

•the power supply system is eﬀectively and properly connected to earth in compliance with regulations in force.

•the socket outlet to connect the installed equipment is within reach.

Some types of equipment can be equipped with a cable without a plug; in this case, the type of plug to use is a "standardised" one, keeping in

mind that the yellow-green wire must be used for earthing, the blue wire must be used for neutral, and the brown wire must be used for the phase.

The power supply cable must be assembled with a plug suitable for the load and connected to an adequate safety plug.

If the ﬁxed equipment is not provided with a power supply cable and plug, or any other device that ensures disconnection from the electrical mains,

with an opening gap of the contacts that enables total disconnection in overvoltage category III conditions, said disconnection devices must be

provided in the mains power supply in compliance with installation regulations.

The yellow/green earth cable must not be cut oﬀ by the switch.

The Manufacturer declines all responsibility for failure to comply with the safety regulations.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Falmec Atlas Vetro Wall in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 8,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Falmec Atlas Vetro Wall Manual

Product: