Installation operations are to be carried out by skilled and qualied installers in accordance with the instructions in this booklet
and in compliance with the regulations in force.
•Before installing the hood, check the integrity and function of each part. Should anomalies be noted, do not proceed with installation
and contact the Dealer.
•Do NOT install the hood if an aesthetic defect has been detected. Put it back into its original package and contact the dealer. No claim
can be made for aesthetic defects once the hood has been installed.
•During installation, always use personal protective equipment (e.g. accident-prevention shoes) and adopt prudent and proper conduct.
•The xing kit (screws, plugs, and brackets) supplied with the hood can only be used on masonry walls: should it be necessary to install
the hood onto walls in a different material, assess other fixing systems keeping the wall resistance and weight of the hood in mind (indicated on
page 3).
•Keep in mind that installations with different types of fixing systems from those supplied, or which are not compliant, can cause electrical and
mechanical seal danger.
•Do not modify the electrical, mechanical and functional structure of the equipment.
•Do not install the hood outdoors and do not expose it to atmospheric agents (rain, wind, etc.).
•After the stainless steel hood has been installed, it will need to be cleaned to remove any residues from the protection adhesive as well as any grease
and oil stains which, if not removed, can cause irreversible damage to the hood surface. To do so the manufacturer recommends using the supplied
moist wipes, which are also available sold separately.
ELECTRICAL SAFETY
The electrical system to which the hood is to be connected must be according to standard and compulsorily supplied with
earthed connection in compliance with safety regulations in the country of use. It must also comply with European standards
regarding radio antistatic properties.
•Before installing the hood, check that the electrical mains power supply corresponds with what is reported on the identification plate located
inside the hood.
•The socket used to connect the installed equipment to the electrical power supply must be within reach: if this is not possible, install a mains
switch in an accessible position in order to disconnect the hood when required.
•Any changes to the electrical system required to install the hood must be carried out by a qualified electrician.
•The maximum length of the flue fixing screws (supplied by the manufacturer) must be 10 mm. Use of non-compliant screws with these instruc-
tions can lead to danger of an electrical nature.
•It is dangerous to change, or try to change, the features of this equipment. Do not try to solve the problem yourself in the event of equipment
malfunction, but contact the Dealer or an authorised Servicing Department for repairs.
•When installing the hood, disconnect the equipment by removing the plug or switching o the main switch.
•
FUMES DISCHARGE SAFETY
•Do not connect the equipment to discharge pipes of fumes produced from combustion (for example boilers, replaces, etc.).
•Before installing the hood, ensure that all standards in force regarding discharge of air out of the room have been complied with.
USER WARNINGS
GENERAL WARNINGS
These warnings have been drawn up for your personal safety and those of others. You are therefore kindly asked to read the
booklet carefully in its entirety before installing and using the equipment or carrying out cleaning operations.
•The Manufacturer declines all responsibility for any damage caused directly, or indirectly, to persons, things and pets as a con-
sequence of failing to comply with the safety warnings indicated in this booklet.
•It is imperative that this instructions booklet is kept together with the equipment for any future consultation. If the equipment is sold
or transferred to another person, make sure that the booklet is also supplied so that the new user can be made aware of the hood's
operation and relative warnings.
•Installation operations are to be carried out by a skilled and qualied installer in accordance with the instructions in this booklet and
in compliance with the regulations in force.
•DO NOT use the hood if the power supply cable or other components are damaged. Disconnect the hood from the electrical power supply
and contact the Dealer or an authorised Servicing Department for repairs. Insist on original spare parts. Do not personally try to carry out re-
pairs or replacements. Interventions carried out by incompetent and unauthorised persons can cause damage, even serious, to things
and/or persons not covered by the Manufacturer's warranty.
•Do not modify the electrical, mechanical and functional structure of the equipment. Any changes to the electrical system required to install the
hood must be carried out by a qualified electrician.
INTENDED USE
•The equipment is solely intended to be used to extract fumes generated from cooking food in non-professional domestic kitchens: any
other use is improper, can cause damage to persons, things and pets and exempts the Manufacturer from any liability.
•The equipment can be used by children above the age of 8 and by persons with reduced physical, sensory and mental abilities, or with no expe-
rience or knowledge, as long as they do so under supervision or after having received relative instructions regarding safe use of the equipment
and understanding of the dangers connected to it. Children are not to play with the equipment. Cleaning and maintenance operations intended
for the user must not be carried out by children without supervision.
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Falmec Atlas Vetro Wall at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Falmec Atlas Vetro Wall in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.
The manual is 8,5 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
