500344

Falcon Toledo XT 110 Manual

47
Zoom out
Zoom in
Previous page
1/60
Next page
47
INSTALLATION
Check the ap pli ance is electrically safe and gas sound when you have fi nished.
Screw the connector into the cooker inlet until it is fi nger
tight. Using two suitable tools, one on the inlet on the
cooker to make sure it is held steady and one on the
connector, tighten the connector into the inlet on the
cooker.
Minimum torque 15Nm.
Maximum torque 20Nm
Connect the hose to the connector.
In the UK
For Natural Gas the fl exible hose must be in
accordance with B.S.669.
For LP Gas it should be capable of 50mbar
pressure, 70°C temperature rise and carry a red
stripe, band or label.
If in doubt contact, your supplier.
Screw connect the threaded end of the hose into the gas
inlet in the underside of the connector block on the back of
the cooker.
The hose should be fi tted so that both inlet and outlet
connections are vertical so that the hose hangs downwards
in a ‘U’ shape.
Because the height of the cooker can be adjusted and
each connection is diff erent it is diffi cult to give precise
dimensions. Ideally the house supply connection should be
in the shaded area shown in the fi gure showing the back of
the cooker. (‘B’ in the fi gure)
After completing the gas connection, check the cooker
is gas sound with a pressure test. When checking for gas
leaks do not use washing up liquid - this can corrode. Use a
product specifi cally manufactured for leak detection.
Pressure testing
The gas pressure can be measured at the injector of one
of the centre hotplate burners. Remove the pan support,
burner head and cap. The injector is now accessible.
See Technical data section at the back of this book for test
pressures.
Reassemble burner top, making sure it is reassembled in the
correct way on the burner body.
Electrical Connection
This appliance must be installed by a qualifi ed electrician
to comply with the relevant regulations and also the local
electricity supply company requirements.
WARNING: THIS APPLIANCE MUST BE EARTHED
Note
The cooker must be connected to the correct electrical
supply as stated on the voltage label on the cooker, through
a suitable cooker control unit incorporating a double pole
switch having a contact separation of at least 3mm in all
poles. This cooker must not be connected to an ordinary
domestic power point.
The total electrical load of the appliance is approximately
5.1kW. The cable size used should be suitable for this load
and comply with all local requirements.
Access to the mains terminal is gained by removing the
electrical terminal cover box on the back panel.
Connect the mains cable to the correct terminals for your
electrical supply type.
Check that the links are correctly fi tted and that the terminal
screws are tight. Secure the mains cable using the cable
clamp.
Current Operated Earth Leakage Breakers
Where the installation is protected by a 30-milliamp
sensitivity residual current device (RCD), the combined
use of your cooker and other domestic appliances may
occasionally cause nuisance tripping. In these instances the
cooker circuit may need to be protected by fi tting a100mA
device. This work should be carried out by a qualifi ed
electrician.
Hotplate
Check each burner in turn. There is a fl ame safety device
that stops the fl ow of gas to the burner if the fl ame goes
out. For each burner, turn the control knob to the large
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon Toledo XT 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon Toledo XT 110 in the language / languages: English, French as an attachment in your email.

The manual is 1,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info