69964
51
Zoom out
Zoom in
Previous page
1/60
Next page
51
English
The handles should be above the fi xings.
Remove the 4mm Allen screws from the top corners of the
fascia and fi x the front handrail in position.
Fitting the splash back (optional)
Remove the two fi xing screws (3mm hexagonal socket head)
and nuts that pass through the top of the rear fl ue grille. Hold
the splash back in position. From the rear refi t the 2 fi xing
screws and nuts.
Gas Connection
Restraining device
A restraining device should be fi tted when the cooker is
connected to a fl exible gas supply. Any restraining device
should be secured to the fabric of the building and should be
able to be released so that the cooker can be pulled out for
cleaning and maintenance.
Flexible Gas Hose
A gas shut off valve must be fi tted between the gas supply
and the connection hose. The fl exible hose (not supplied
with the cooker) must be in accordance with the relevant
standards. If in doubt contact, your supplier.
The inlet connection on the cooker is ISO 7-1 internal. If you
require a ISO 228-1 connection fi nd the ISO 7-1 to ISO 228-
1 connector in the conversion kit. Apply a suitable thread
sealing compound to the ISO 7-1 end.
Screw the connector into the cooker inlet until it is fi nger
tight. Using two suitable tools, one on the inlet on the cooker
to make sure it is held steady and one on the connector,
tighten the connector into the inlet on the cooker.Minimum
torque 15Nm.Maximum torque 20NmConnect the hose to
the connector.
The hose should be fi tted so that both inlet and outlet
connections are vertical so that the hose hangs downwards in
a ‘U’ shape.
view from the rear
A appliance gas inlet
B position for gas supply connector
C alternativley connect from the side.
Because the height of the cooker can be adjusted and each
connection is diff erent it is diffi cult to give precise dimensions.
Ideally the house supply connection should be in the shaded
area shown in the fi gure showing the back of the cooker (‘A in
the fi gure). Alternatively connect from the side.
After completing the gas connection, check the cooker is gas
sound with a pressure test. When checking for gas leaks do
not use washing up liquid - this can corrode. Use a product
specifi cally manufactured for leak detection.
CAUTION: DO NOT USE A FLAME TO CHECK FOR GAS LEAKS.
Pressure testing
The gas pressure can be measured at the pressure test point
on the gas connection block. Turn and light one of the
hotplate burners.
Reassemble burner top, making sure it is reassembled in the
correct way on the burner body.
Electrical Connection
This appliance must be installed by a qual i ed electrician
to comply with the relevant In sti tute of Electrical Engineers
(I.E.E.) regulations and also the local elec tric i ty supply
company re quire ments.
WARNING: THIS APPLIANCE MUST BE EARTHED
Note
The cooker must be connected to the cor rect electrical
supply as stated on the voltage la bel on the cooker, through
a suitable cooker control unit incorporating a double pole
switch having a contact separation of at least 3mm in all
poles. This cooker must not be connected to an ordinary
domestic power point.
The total electrical load of this appliance is 11.1kW at 230VAC
It must be connected to an electrical supply, either single
phase or multi phase that can sustain a maximum current
ow of at least 48 amps. (Unless local regulations allow this
loading to be reduced by applying diversity factors).
51


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon Classic Deluxe 110 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon Classic Deluxe 110 in the language / languages: English, German as an attachment in your email.

The manual is 2,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Falcon Classic Deluxe 110

Falcon Classic Deluxe 110 User Manual - Dutch - 36 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info