500338
24
Zoom out
Zoom in
Previous page
1/32
Next page
WARNING - SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity supply before servicing. Check appliance is safe when you have finished.
Page 24
Installation and
Servicing Instructions
This appliance must be installed and serviced by a
competent person.
IMPORTANT
The unit shall be installed in accordance with the regulations
in force at the time. Read the instructions thoroughly before in-
stallation and subsequent use.
In the UK, regulations and standards are as follows -
BS 6891 :1988
Health And Safety At Work etc. Act
BS 7671 I.E.E. Regulations for Electrical Installations
Local and National Building Regulations
Electricity at Work Regulations
Fire Precautions Act
The appliance has been CE-marked on the basis of compli-
ance with the Low
Voltage and EMC directives for the voltage stated on the data
plate.
WARNING - ALL APPLIANCES MUST BE EARTHED
On completion of the installation, this manual should be left
with the Engineer-in-Charge for reference during servicing.
Further to this, The Users Manual should be handed over to
the Owner, having had a demonstration of the operation and
cleaning of the unit.
IT IS IMPORTANT THAT THESE INSTRUCTIONS BE
CONSULTED PRIOR TO INSTALLING AND COMMIS-
SIONING THIS APPLIANCE.
FAILURE TO COMPLY WITH THE SPECIFIED PROCE-
DURES MAY RESULT IN DAMAGE OR THE NEED
FOR A SERVICE CALL.
SECTION 1 - INSTALLATION
UNLESS OTHERWISE STATED, PARTS WHICH HAVE
BEEN PROTECTED BY THE MANUFACTURER ARE
NOT TO BE ADJUSTED BY THE INSTALLER.
1.1 MODEL NUMBERS, NETT WEIGHTS AND
DIMENSIONS
Model Width Depth Height Weight
211-EEO 1100mm 600mm 935mm 140kg
1.2 SITING
1.2.1 Positioning the Appliance (see Figure 1)
Figure 1
The unit is supplied with two rear and one centre front roller for
movement purposes.
To position the range, first remove the kicking strip from the bot-
tom front of the unit. Pull open the drawer to the furthest point
and lift and pull it forward to remove. The screw that lowers the
front roller is positioned at the LH side of the drawer opening on
the centre support beam.
Place the flat end of the spanner over the square drive peg and
turn this clockwise until the front beam and feet are clear of the
floor. Use the hex end of the spanner to turn the two adjusting
nuts, positioned at either bottom front corner. Six complete turns
clockwise will lower the back rollers and raise the unit rear.
The unit may now be pushed into position.
THE APPLIANCE MUST NOT BE PUSHED, PULLED OR
LIFTED BY THE TOWEL RAIL OR DOOR HANDLES.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon 211 EEO Ceramic at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon 211 EEO Ceramic in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info