500342

Falcon 1092 CT Dual Fuel Manual

30
Zoom out
Zoom in
Previous page
1/36
Next page
SERVICING  WARNING
Disconnect from electricity and gas before servicing. Check appliance is safe when you have finished.
30
Servicing
1 Servicing
When servicing or replacing gas carrying components,
disconnect from the gas supply before commencing
operation.
Check the appliance is gas sound after completion of
service. When checking for gas leaks do not use washing
up liquid - this can corrode. Use a product specifi cally
manufactured for leak detection.
Do not use re-conditioned or unauthorised gas controls.
Disconnect from the electricity supply before
commencing servicing, particularly before removing any
of the following: - control panel, side panels, hotplate tray
or any electrical components or covers.
Before electrical re-connection, check that the appliance
is electrically safe.
Note - References to LH and RH oven apply as viewed
from the front.
BEFORE SERVICING ANY GAS CARRYING COMPONENTS.
TURN OFF THE GAS SUPPLY.
2 To Remove the Hotplate
Disconnect the appliance from the electricity supply. Pull
the unit forward to gain access.
a) Remove the French cooktop/pan supports/hotplate
accessories and burner caps.
b) Remove the brass venturi in the centre of each
hotplate burner bezel.
c) Remove the bezel from the hotplate and disconnect
the spark ignition lead from the spark electrode.
d) Lift the hotplate clear of the appliance.
e) Replace in reverse order.
3 To Remove the Control Panel
Disconnect the appliance from the electricity supply.
a) Remove the pan supports/hotplate accessories and
burner caps.
b) Slacken the brass venturi at the centre of each burner.
c) Remove the control knobs from all taps.
d) Open the grill and RH oven doors. Remove 3 fi xings
on the top front and 3 fi xings on the control panel
underside.
e) Pull the control panel forward. Remove the
connections from the rear of the three neons.
Disconnect the earth lead and lift the panel clear of
the unit.
f) Replace all parts in reverse order.
g) When replacing any electrical connections refer to the
wiring diagram.
4 To Remove an Outer Side Panel
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 3
b) Remove the retaining screw on the upper front edge
and the two fi xings on the rear or the side panel. Undo
the lower retaining screw situated below the edge at
the panel front corner.
c) Remove the panel by pulling it away from the unit.
Should diffi culty be encountered, it may be necessary
to slacken the two closest burners and both brass
venturi as detailed in Section 2.
d) Replace parts in reverse order. Ensure that both
venturis are fully tightened.
5 To Remove an Oven or Grill Neon
Disconnect the appliance from the electricity supply.
a) Remove the control panel as detailed in Section 3
b) Remove the relevant neon connection and undo the
nut which secures the neon to the control panel.
c) Replace parts in reverse order. Ensure the replacement
neon functions correctly.
6 To Remove a Thermostat
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 2.
b) Remove the control panel as detailed in Section 3
c) Open the appropriate oven door and remove the oven
shelves.
d) Pull the unit forward to gain access to the cover box.
Undo the cover screws and lift clear.
RH oven
Remove the two fi xings that secure the thermostat
phial cover. Unclip the thermostat phial from the clips
in the oven back panel.
LH oven
Remove the two screws holding the thermostat phial
to the oven fan cover at the rear of the oven. Pull the
unit forward to access the rear of the cooker. Remove
the both cover boxes by removing the fi xing screws
and lifting clear. Feed the thermostat capillary clear of
the oven.
e) Disconnect the wires from the thermostat and undo
the two fi xings which secure the control to the
mounting plate.
f) Fit the replacement and re-assemble in reverse order.
Ensure that the phial is clipped to the oven rear,
positioned centrally between the clips. Check that the
thermostat functions correctly.
7 To Replace a Grill Controller
Disconnect the appliance from the electricity supply.
a) Remove the hotplate as detailed in Section 2.
b) Remove the control panel as detailed in Section 3.
c) Disconnect the controller wiring. Undo the fi xings that
secure the device to the mounting plate.
d) Fit the replacement and re-assemble parts in reverse
order. Check that the replacement functions correctly.
… 30 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon 1092 CT Dual Fuel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon 1092 CT Dual Fuel in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info