500342

Falcon 1092 CT Dual Fuel Manual

24
Zoom out
Zoom in
Previous page
1/36
Next page
24
Conversion to LP
If the appliance is to be converted to LP gas do the
conversion at this point. See the conversion section of
these instructions.
Levelling
You are recommended to use a spirit level on a shelf in
one of the ovens to check for level.
Place the cooker in its intended position taking care not
to twist it within the gap between the kitchen units as
damage may occur to the cooker or the units.
The rollers can be adjusted to level the cooker. To adjust
the height of the rear of the cooker use the levelling tool
supplied to turn the adjusting nuts at the front bottom
corners of the cooker.
Adjust the height of the front roller to level the cooker.
Turn clockwise to raise the cooker and anticlockwise to
lower.
When you are satisfi ed with the height and level raise the
front of the cooker by one turn of the front roller adjuster.
Screw down the front feet to meet the fl oor. Screw the
front roller adjuster anticlockwise to raise the front roller
so that the front of the cooker is supported on the feet,
not the front roller, to prevent accidental movement of
the cooker.
Gas Connection
Fitting a stability bracket
A stability bracket or chain (not supplied by with the
cooker) should be fi tted when the cooker is connected
to a fl exible gas supply. Any restraining device should be
secured to the fabric of the building and should be able
to be released so that the cooker can be pulled out for
cleaning and maintenance.
When fi tting a stability bracket read these instructions
together with the leafl et supplied with the bracket.
a) Position and level the appliance.
b) Draw a pencil line 68mm from the front edge of the
levelling feet.
c) Mark off 300mm from the RH side of the unit to
indicate the centre line for the bracket.
d) Remove the unit.
e) Mark off 595mm to locate the front edge of the lower
bracket. Fix bracket to fl oor.
f) Measure the height from fl oor level to the top edge
of the rear channel. Add 3mm to this dimension and
assemble the stability bracket to this height (i.e. from
fl oor level to underside of top member)
Gas Connection
The Gas supply needs to terminate with a down facing
bayonet. The rear cover boxes limit the position of the
supply point.
view from the rear
A position for gas supply connector
B appliance gas inlet
Because the height of the cooker can be adjusted and
each connection is diff erent it is diffi cult to give precise
dimensions. Ideally the house supply bayonet should
be in the shaded area shown in the diagram. Although
a 900mm hose can be used, a 1250mm hose will allow
slightly more fl exibility in the positioning of the bayonet
and make moving the cooker easier. The hose should be
fi tted so that both inlet and outlet connections are vertical
so that the hose hangs downwards.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Falcon 1092 CT Dual Fuel at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Falcon 1092 CT Dual Fuel in the language / languages: English as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info