Manual Fagor FET-5112 (page 19 of 40) (English, German, French, Italian)

554737

Zoom out

Zoom in

1/40

NB:

Before calling for your breakdown engineer, we would recommend that

you do the following:

- Set the Programme selector to the

« »

position and remove the electrical

plug for at least 10 seconds.

- Reconnect the plug and restart a washing cycle.

If the fault displayed persists, call your breakdown engineer and remember

to tell him which indicator lights were lit.

Important:

Do not restart a washing cycle if the drum remains locked or if

you notice water around your machine of if you notice a burning sme.

• AFTER-SALES SERVICE:

Possible maintenance on your washing machine should be undertaken by:

— either your dealer,

— or another qualied mechanic who is an authorized agent for the brand

appliances.

When making an appointment, state the complete reference of your

equipment (model, type and serial number). This information appears on

the manufacturer’s nameplate attached to the rear of the equipment.

• INCIDENTS THAT MAY OCCUR

• The cycle does not start

– You have not pressed the «

start/pause

» button.

– There is no power to the machine:

- Check that the plug is correctly in the socket

- Check the circuit breaker and the fuses.

– The water tap is closed

– The machine’s lid is not closed properly

• A puddle of water forms around the machine

Warning:

First of all remove the plug and the fuse and shut off the water

supply tap.

While the machine is operating, the permanent level control prevents the

water from overowing. If, despite this, water comes out of your machine,

it may be that:

– The drain hook is wrongly positioned in the drain pipe.

– The water supply hose is not sealed tightly at the machine or tap end:

- Check that the seals are in place and the connections are tight.

• Heavy vibration during spin

– All the transport materials have not been removed correctly from the

machine:

- Check that all the transport wedges have been removed (see

. «REMOVING THE TRANSPORT CLAMPS»).

– The oor is not level.

– Your machine is resting on its two «front» castors (depending on the

model):

- Reset your machine on its feet by pushing the castor engagement lever

. to the right.

• The washing is not spun or not spun enough

You have selected a programme with no spin, for example «drip-dry»

– The spin safety system has detected poor distribution of the washing in

the drum:

- Untangle the washing and programme a new spin.

• The machine does not drain

– You have programmed «Full drum stop»

– The pump lter is blocked:

- Clean it (see «CLEANING THE PUMP FILTER» for the relevant

procedure)

– The drain hose is kinked or squashed

• The lid does not open

– The programme has not yet nished

The lid remains locked throughout the programme.

• The drum doors open very slowly

(On machines tted with gently opening doors)

– Your machine has not operated for a long time

– It is located in too cold a position.

– Detergent residue (powder) is blocking the hinges

- In all cases, everything returns to normal after the doors have opened

initially

Important :

As a general rule, whatever the anomaly detected, you should

stop the machine, unplug the power cable and shut off the water tap.

6 / INCIDENTS AND MEANING OF PARTICULAR LIGHTS FLASHING EN

• MESSAGES INDICATED BY THE VARIOUS

LIGHTS FLASHING

• Incidents indicated, which you can rectify yourself

In this section, we explain how you can rectify these incidents very

easily yourself.

Your machine automatically detects some operating incidents and indicates

these by particular options lights ashing.

Lights ashing Causes / Remedies

The water tap is closed. Check that the water

tap is open and then press the «

start/pause

button again to restart the cycle. This incident may

also be caused by the drain hose being poorly

connected (see the section «DRAINING AWAY

THE WASTE WATER»).

The pump lter is clogged. Clean the pump lter

(for how to do this, see the section «CLEANING

THE PUMP FILTER») and then press the «

start/

pause

» button again to restart the cycle.

Also check the drain hose’s position in the drain:

the connection must not be airtight (see the section

«DRAINING AWAY THE WASTE WATER»).

Lid not closed properly. Check that the lid is

closed and then press the «

start/pause

» button

again to restart the cycle.

Drum blocked. Check that a small item of laundry

(e.g. a handkerchief or a sock, etc.) has not

slipped down between the tub and the drum and

is stopping the drum from turning. To access the

bottom of the tub, please refer to the section

«CLEANING THE PUMP FILTER».

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Fagor FET-5112 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 2,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Fagor FET-5112 Manual

Product: