Manual Faema E61 Jubile (page 27 of 42) (English, German, French, Italian, Portuguese, Spanish)

649152

Zoom out

Zoom in

1/42

EnglishEnglish

Defects - Malfunctions

Direct action by the customer

Before calling service personnel, to avoid useless expense, check whether the machine problem corresponds to one of the

cases listed below.

Defects - Malfunctions

PROBLEM

Leaking from the filter-holder rim (10).

Coffee dispensing time too short.

Coffee drips out of machine.

Loss of water under the machine.

SOLUTION

Clean using the special brush provided.

Use a finer grind.

Use new coffee.

Clean.

Use a coarser grind.

Clean.

CAUSE

Underpan gasket dirty with coffee.

Coffee ground too coarse.

Coffee too old.

Filter holes blocked or filter-holder (10)

outlet hole dirty.

Coffee ground too fine.

Discharge well clogged up.

Discharge pan hole blocked.

Interventions by a specializes technician

PROBLEM

Infusion time too short

Rapid dispensing.

Coffee very bland, without cream.

(Same defects on all groups).

Infusion time very short.

Rapid dispensing.

Coffee very bland, without cream.

(Same defects on all groups).

Low coffee yield.

Slow dispensing.

Coffee cold and bland.

Fast dispensing, coffee bland.

Pressure gauge pump indicates

pressure greater than 9 bar.

Low coffee yield.

Fast dispensing.

Coffee hot and bland.

Coffee cold, bland and without cream.

Normal infusion and dispensing times.

Coffee cold in the morning at start of work.

SOLUTION

This defect is associated to other

secondary symptoms which may be

caused by a number of other causes as

per the previous points. Do not adjust the

machine until all other causes have been

excluded.

The capacity of the group without filter

must be 100 cm³ in 8 ÷ 10 seconds.

If the group is operated without the filter-

holder, thin, isolated jets will be

dispensed instead of one central jet.

Coffee grounds in cup.

Move group to and fro to remove air bubble.

When touching the water tube it is warm

near to the machine.

Pressure gauge calibrated with values

that are too low.

See switching on instructions.

CAUSE

Coffee grounds too course.

Old coffee.

Group nozzle widened through use.

OR gasket in cone-shaped section

leaks.

Infusion valve remains open

Filter edge broken.

Spout dirty.

Pump out of calibration.

By-pass valve blocked.

Filters with perforations widened.

Coarse grinding.

Air bubble in thermosiphon circulation.

Check valve does not hold (with low

pressure in system).

Heat exchangers emptied.

Heat exchanger defective (shows

pressures higher than real values).

Air in boiler.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Faema E61 Jubile in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,86 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Faema E61 Jubile Manual

Product: