Manual Faber Farum (page 43 of 64) (English, German, Dutch, Danish, Norwegian)

525643

Zoom out

Zoom in

1/64

42 < < < <

6.6.1 Placing the imitation logs

 Place the imitation logs. Make sure

that the logs are properly connected

to the tube burners.(see fig. 4.1 or

imitation logs instruction card

supplied)

 Now divide the vermiculate pebbles

and the chips in the combustion

chamber. Avoid the covering of the

air vent(s).

 Place the glass and check the fire

image.

6.6.2 Pebbles

 Place the pebbles over the burner and

the bottom. Spread the pebbles

evenly to a double layer. The surface

of the pebbles may be very slightly

higher than the burner tube ( zie fig.

4.2)

 Place the glass and check the flame

picture into the appliance

6.7 Checking the installation.

6.7.1 Checking the ignition of the pilot

burner, main burner.

Start the pilot and main burner according

to the instructions in the user’s manual.

 Check whether the pilot light is

properly positioned above the main

burner and is not covered by chips, an

imitation log or pebbles.

 Check the ignition of the main burner

at full mark or low mark.

(the ignition should take place

quickly and easily).

6.7.2 Checking for gas leakage.

Check all connections and joins for possible

gas leaks by means of a gas leak detector or

spray

6.7.3 Checking the burner pressure

and the pre-pressure

Check whether the burner pressure and the

inlet pressure measured agree with the data

indicated on the registration plate

Measuring the inlet-pressure:

 Turn off the gas control tap.

 Open the pressure gauge nipple A (see

figure 1.1 ) a few turns and connect

a pressure gauge hose to the gas

control valve.

 Carry out this measurement when the

appliance is on at full gas mark and

when it is on the pilot light.

 If the inlet pressure is too high you

are not permitted to connect the

appliance.

Measuring the burner pressure:

Only perform this measurement if the

inlet-pressure is correct.

 Open the pressure gauge nipple B (see

fig. 1.1 ) a few turns and connect a

pressure gauge hose to the gas control

valve.

 The pressure must agree with the

value indicated on the registration

plate. In case of deviations, get in

touch with the manufacturer.

* Close the pressure gauge nipples and

check these for gas leaks.

6.7.4 Checking the flame picture.

Allow the applaince to burn for at least 20

minutes at full and then check the flame

picture for:

7. Distribution of the flames

8. Colour of the flames

If either one or both points are

unacceptable, then check:

 The positioning of the imitation logs

and/or the quantity of pebbles or

chips on the burner.

 The connections of the Flue materials

for leakage (in case of blue flames)

 Whether the correct flue restrictor

has been mounted

 The outlet .

o Wall terminal is installed

correctly

o Roof terminal is fitted and

sited correctly

 The flue system is correctly

calculated

6.8 Instructing the client

 Recommend that the appliance be

serviced annually by a competent

person in order to guarantee a safe

use and a long lifespan.

 Advise and instruct the client about

maintenance and cleaning of the

glass. Emphasize the risk of burning in

fingerprints.

 Instruct the client about the

operation of the appliance and the

remote control unit, including the

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Faber Farum in the language / languages: English, German, Dutch, Danish, Norwegian as an attachment in your email.

The manual is 1,63 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Faber Farum Manual

Product: