706323

Faber Cas 1000 Manual

15
Zoom out
Zoom in
Previous page
1/50
Next page
• is the test mode button. This will be used by the manufacturer and the Service Engineer
• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep
when you reach the minimum level
• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible
beep when you reach the maximum level
• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase re crackling sound. Press this to increase the volume of the crackling sound.
Button panel ‘B’:- Controls the functioning of the left side of appliance
• is the test mode button. This will be used by the manufacturer and the Service Engineer
• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep
when you reach the minimum level
• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible
beep when you reach the maximum level
• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase re crackling sound. Press this to increase the volume of the crackling sound.
GETTING THE DESIRED FLAME EFFECT
1. Switch the appliance on by pressing the main switch to the on position and pressing the on/standby button. The
ames will start after 45seconds. The ames will be at max height for 5seconds and then reduce to a nominal level
2. Press the and buttons to adjust the ame to your desired level. Please give the ame generator time to react
to the changes you make.
3. Do not tilt or move the appliance while there is water in the tank or sump
4. Make sure that the appliance is on a level surface
Once you have made you adjustments to both the ame height and crackling sound the appliance will keep these
settings even if you power off the appliance by either the on/standby button or by the main switch. The next time you
switch on the appliance it will start up as normal, wait 45 seconds for the ames to start, run at maximum height for 5
seconds and then revert to the adjusted settings.
RECEIVER CONTROLS
There are manual controls on the Receiver
CAS500
• is the on/standby button. Press it to turn on and off the ame effect.
• is the re crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep
when you reach the minimum level
• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible
beep when you reach the maximum level
CAS1000
• is the on/standby button. Press it to turn on and off the ame effect.
• is the re crackling sound. Press this to turn on and off the crackling sound. The volume is adjusted on the
manual controls of the appliance
• is the reduce ame button for the left had side of the appliance. Press this to reduce the height/intensity of your
ame. You will hear an audible beep when you reach the minimum level
• is the increase ame button for the left had side of the appliance. Press this to increase the height/intensity of
your ame. You will hear an audible beep when you reach the maximum level
• is the reduce ame button for the right had side of the appliance. Press this to reduce the height/intensity of your
ame. You will hear an audible beep when you reach the minimum level
• is the increase ame button for the right had side of the appliance. Press this to increase the height/intensity of
your ame. You will hear an audible beep when you reach the maximum level
REMOTE CONTROL
The remote control is supplied with 2xAAA batteries. Remove the battery cover from the underside of the remote control
and after removing the batteries from the plastic wrapping t them into place. Replace the battery cover.
The remote control has wireless technology and is required to be paired to the receiver. This is done by pressing the
button on Button Panel ‘A’, the LED’s will start to blink on and off. This is to let you know that the appliance is ready to
connect to the remote control. Press the button on the remote control. The appliance will switch off. Now the remote
control is paired to the appliance.
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Cas 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Cas 1000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info