706323

Faber Cas 1000 Manual

14
Zoom out
Zoom in
Previous page
1/50
Next page
Operating the Product
4. Turn on the internal ball valve. This is located under the sump. Remove the sump as described under ‘Cleaning’ in
the Maintenance section
Please note: the water pressure is to be between 8Bar (800Kilopascals) and 0.5Bar (50Kilopascals).
If you do not feel condent making this connection please consult a qualied plumber, to ensure a safe and
secure installation.
Electrical Connection
Plug the re into a 13amp/240 volt outlet. Be sure to have access to the plug after installation to allow for disconnection.
Ensure that the supply cable exits at the back of the re, at the right or left hand corner to suit your supply socket location
and is not trapped under the re such that it might cause it to be damaged. If connecting multiple appliances into the
same outlet be sure not to connect more that 5 appliances. If more appliances are required they must be connected into
a separate circuit.
The appliance can be connected to the xed wiring of the premises through a suitable connection box positioned
adjacent to the appliance. This electrical installation must be carried out by a competent electrician and be in strict
accordance with the current I.E.E regulations for Electrical Equipment in Buildings.
The electrical can remove the supplied plug by the following;
1. Lift off the fuelbed and put switch ‘A’ into the off position (Fig 9).
2. Ensure that the appliance is unplugged.
3. Lift off the access cover by removing the retaining screw (Fig 15).
4. Unscrew and remove the Live, Neutral and Earth wires.
5. Unscrew the cable clamp (Fig 16 ‘A’) and remove the supply cord.
The electrician can then connect their wire from the appliance (by following the steps above in reverse) to the connection
box ensuring that it incorporates a double pole isolating switch having a contact separation of at least 3mm. Brown - Live
(L), Blue - Neutral (N) and Green/Yellow - Earth (E).
Connecting the Receiver
Take your Receiver, 4button for CAS500 and 6button for CAS1000, and with the Fuelbed removed insert the 3.5mm
jack into the socket at the back of the appliance (Fig.5). The Receiver has a cable length of 1.4m which will allow you
position it anywhere around the product. If you prefer to hide it the Receiver can be placed inside the surround/wall.
Please ensure that the Receiver is not enclosed in metal, concrete or any other dense material, this will affect the signal
from the remote control.
This section describes how to activate your re using either the manual controls or remote control.
MANUAL CONTROLS
The manual controls are located beneath the Fuelbed. (Fig.6)
CAS500
Mains Switch ‘A’:- Controls the electricity supply to the appliance.
Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate
Button panel ‘A’:- Controls the functioning of the appliance
• is the on/standby button. Press it to turn on and off the ame effect. Turning it on will be indicated by the main
lights activating. Although the main lights operate immediately it will take a further 45 seconds before the ame effect
starts.
• is the Pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for details
• is the test mode button. This will be used by the manufacturer and the Service Engineer
• is the reduce ame button. Press this to reduce the height/intensity of your ame. You will hear an audible beep
when you reach the minimum level
• is the increase ame button. Press this to increase the height/intensity of your ame. You will hear an audible
beep when you reach the maximum level
• is the reduce re crackling sound. Press this to reduce the volume of the crackling sound. The minimum volume
for this is off
• is the increase re crackling sound. Press this to increase the volume of the crackling sound.
CAS1000
Mains Switch ‘A’:- Controls the electricity supply to the appliance.
Note: This switch must be in the ‘ON’ ( I ) position for the appliance to operate
Button panel ‘A’:- Controls the functioning of the left side of appliance
• is the on/standby button. Press it to turn on and off the ame effect. Turning it on will be indicated by the light
activating. Although the main lights operate immediately it will take a further 45 seconds before the ame effect
starts.
• is the Pairing button. This will pair your remote control to the receiver. See ‘Remote Control Operation’ for details
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Faber Cas 1000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Faber Cas 1000 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,72 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info