Manual FAAC XT2 (page 2 of 4) (English, German, Dutch, French, Italian, Spanish)

626605

Zoom out

Zoom in

1/4

2 3

DESCRIPTION ÉTIQUETTE ( Figure 2 )

A - Code d’identification du modèle

B –

Numéro d’identification du lot de production

C – Lire les instructions

D – Éliminer selon les directives en vigueur

E - Référence organisme notifié (notified body)

Fréquence de fonctionnement

868.92 MHz ±100KHz

Type batterie 2 piles 3 V au lithium

CR2032

Usage exclusif

Ouvre-portail

Ce produit est conforme à la directive

99/05/CEE

TO RECOGNISE A MASTER/SLAVE TX

•master : if you press any key of a master TX, the LED

flashes before becoming steady.

•slave : if you press any key of a slave TX, the LED

goes on immediately with steady light.

PROGRAMMING SEQUENCE

1)Power up the system after installing and connecting

the electrical components of the 868 SLH System.

2)Use a master TX to set the “site code” on the deco-

ding card/RP receiver (see “system coding”).

3)Use the same master TX to set the “site code” on

the system’s other TXs (See “TX coding”).

4)Coded TXs are automatically stored in the de-

coding card/RP receiver by simply activating the

transmitter channel twice in succession within 5

seconds.

SYSTEM CODING

•Simultaneously press push-buttons P1 and P2 of the

master TX and release them when the LED flashes

(after about one second);

•Press and hold down the learning button on the

decoding card/RP receiver: the LED must flash;

•While the master transmitter’s LED is flashing, press

and hold down a channel (the TX’s LED goes on with

steady light);

•Before releasing the learning button on the deco-

ding card/RP receiver, check if the LED goes on with

steady light for a couple of seconds to confirm that

the “site code” was saved.

•Release the button of the master TX channel.

TX CODING

•Simultaneously press push-buttons P1 and P2 of

the master TX used for coding the system and re-

lease them when the LED flashes (after about one

second);

•Frontally bring into contact the master TX and the

TX to be coded (master or slave) ;

•On the master TX (while its LED is flashing), press and

hold down the same channel used for coding the

system: the LED goes on with steady light;

•Press the required channel on the TX to be coded

and release it when the LED goes off after flashing

twice to confirm the “site code” was saved;

•Release the button of the master TX channel;

•Repeat this procedure for every TX to be coded.

COMMENT RECONNAÎTRE UN TX MAÎTRE/ESCLAVE.

•maître : en appuyant sur une touche quelconque

d’un TX maître, la Led clignote avant de s’allumer

avec une lumière fixe.

•esclave : en appuyant sur une touche quelconque

d’un TX esclave, la Led s’allume immédiatement

avec une lumière fixe.

SEQUENCE DE PROGRAMMATION.

1)Alimenter l’installation après avoir effectué l’instal-

lation et les connexions électriques des composants

du Système 868 SLH.

2)Utiliser un Tx maître pour fixer le “code installation”

sur la carte de décodage/ récepteur RP (voir “co-

dage installation”).

3)Utiliser le même Tx maître pour introduire le code

installation sur les autres Tx de l’installation (voir “co-

dage Tx”).

4)Les Tx codifiés seront mémorisés automatiquement

dans la carte de décodage/récepteur RP en activant

simplement deux fois de suite, dans un délai maxi.

de 5 secondes, le canal de l’émetteur.

CODAGE INSTALLATION.

•Appuyer simultanément sur les poussoirs P1 et P2

du Tx maître et les relâcher lorsque la Led clignote

(au bout d’une seconde environ);

•Sur la carte de décodage/récepteur RP, appuyer

et maintenir dans cette position le poussoir d’auto-

apprentissage: la Led doit clignoter;

•Sur le Tx maître (tandis que la Led

clignote) appuyer et maintenir dans cette

position un canal (la Led de l’émetteur s’allume avec

une lumière fixe);

•Sur la carte de décodage/récepteur RP, vérifier l’al-

lumage fixe de la Led pendant deux secondes, pour

avoir la confirmation que la mémorisation du “code

installation” a eu lieu, avant de relâcher le poussoir

d’apprentissage;

•Relâcher le poussoir du canal du Tx maître.

CODAGE TX.

•Appuyer simultanément sur les poussoirs P1 et P2

du Tx maître utilisé pour le codage de l’installation et

les relâcher lorsque la Led clignote (au bout d’une

seconde environ);

•Approcher frontalement pour qu’ils se touchent le

Tx maître du Tx à codifier (maître ou esclave);

•Sur le Tx maître (tandis que la Ledclignote), appuyer

et maintenir dans cette position le même canal utilisé

pour le codage de l’installation: la Led s’allume

avec une lumière fixe;

•Sur le Tx à codifier, appuyer sur le canal souhaité et

le relâcher lorsque la Led s’éteint après un double

F - XT2 cod. 787005 XT4 cod. 787006

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of FAAC XT2 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 0,18 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

FAAC XT2 Manual

Product: