560682

FAAC S450H Manual

8
Zoom out
Zoom in
Previous page
1/11
Next page
7
a
b
c
ENGLISH
4 MANUAL OPERATION
OPEN
CLOSED
UNLOCKED
LOCKED
Fig. 18
5 ELECTRICAL CONNECTION OF THE "2easy bus" ENCODER
The S450H operator is fitted with an encoder system with "2easy bus" technology. The proper assignment of the leaf to the corresponding
encoder depends on the connection of the two encoder wires (leaf 1- encoder 1; leaf 2 - encoder 2).
THE ENCODER WIRES MUST BE CONNECTED TO THE "2easy bus" CONNECTOR OF THE ELECTRONIC EQUIPMENT.
To verify the proper combination LEAF 1 - ENCODER 1 - MOTOR 1 and LEAF 2 - ENCODER 2 - MOTOR 2, refer to the LEDs on the
encoders, as shown by table 2 and the figures 19 - 20 - 21.
To invert the leaf-encoder combination, change the encoder polarity by swapping its wires until the right LEDs are lit.
TABLE 2
LED ON BLINKING OFF
DL 1
Power supply ON and BUS - board
communication
Power supply ON but
no BUS communication
(e.g.: cabling fault)
Power supply OFF and no BUS communi-
cation
(e.g.: missing or broken connection)
DL 2 Encoder associated to leaf 1 / Encoder associated to leaf 2
DL 3
/ Pulse reading during leaf movement Leaf stationary
DL 1: must always be ON to ensure the right connection between encoder and board.
DL 2: indicates the leaf where the encoder is installed.
If the encoder is installed on leaf 1, the DL 2 LED is ON.
If the encoder is installed on leaf 2, the DL 2 LED is OFF.
DL 3:
when blinking at regular intervals, it signals the pulse reading during the leaf
movement. When the gate leaf is stationary, DL 3 is OFF.
If the gate is to be operated manually because of a power failure or an automated system fault, activate the release device.
1) Lift the protection lid (Fig. 18, re.
a) and insert the key in the lock (Fig. 18, ref. b).
2) Turn the key 90° clockwise to open the cover and lift it.
3) Turn the release knob (Fig. 18, re. c
) anticlockwise until it stops.
4) Open or close the leaf manually.
To restore the normal operation of the automated system, perform the above described operations in reverse order.
The LEDs of the encoder remain visible also with the protection cover of the rear
bracket installed.
The models S450H SB are not equipped with a release facility since, thanks to the particular configuration of the hydraulic
distributing flange, you do not need to release the operator to manually move the leaf
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FAAC S450H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FAAC S450H in the language / languages: English as an attachment in your email.

The manual is 1,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of FAAC S450H

FAAC S450H User Manual - Dutch - 10 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info