119529
10
Zoom out
Zoom in
Previous page
1/28
Next page
Page 10
January, 2004
412 Operator And
455 D Control Panel Installation Manual
INSTALLING THE 455 D CONTROL
P
ANEL
Locate the control panel enclosure in the most
convenient position possible, considering the movement
of the gate. Figure 12 shows a basic layout for a two-
leaf gate with the 412 Compact Operator.
Installing the control panel consists of the following
general steps:
Connecting the main power to the control
panel
Connecting the activating device
Connecting the operator to the control panel
Checking the direction of the motor's rotation
Connecting other devices to the control panel
Set operating modes
The installer is responsible for grounding the gate and
operator systems, for providing the main power breaker
switch, and for making sure that the entire gate system
meets all applicable electrical codes.
For the complete 455 D Control Panel Installation
Instructions, see pages 14—25 of this manual.
ATTACH THE OPERATOR COVER.
Once the operator is attached to the gate leaf, you
next prepare the cover for installation.
Caution: If you did not correctly establish the
orientation of the gate leaf and properly
install the DX model on the right side and SX
on the left side, you will be unable to install
the cover on either operator.
Position the mounting insert inside the aluminum
cover and then slide the aluminum cover into
position. Secure the cover and insert with the short
screws provided (see Figure 11).
4 3/8 in.
(11 cm)
2 3/4 in.
(7 cm)
Figure 8. Attach the operator to the rear
mounting bracket (an SX version is shown)
Minimum of 3 1/8 in. (8 cm) from
the back of the vertical mounting
plate to the center of the front
mounting hole on the operator
Figure 9. Secure the operator to the front mount-
ing bracket with the short pin and 2 snap rings
Figure 10. Weld the front mounting bracket into position
after insuring the operator is level in the fully closed and
fully opened positions
The plastic cover insert
has a slot that must align
with the slot in the cover
End cap for cove
r
Figure 11. Attach the cover with two screws (SX
model shown)
10


Need help? Post your question in this forum.

Forumrules
1

Forum

faac-455

Reset search

  • Looking for set up program for 455A control board to FAAC 760 dual gate
    Submitted on 9-7-2023 at 01:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for FAAC 455 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of FAAC 455 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of FAAC 455

FAAC 455 User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info