Manual FAAC 455 (page 7 of 28) (English)

119529

Zoom out

Zoom in

1/28

MANUAL RELEASE MECHANISM

The Manual Release mechanism is a built-in release

device of the 412 Operator (see Figure 4). To access the

keyhole, remove the plug on the top of the motor

housing. Then insert the key and turn it a half turn in

the direction of the gate’s closing to disengage the

operator’s motorized operation. You can now move the

gate leaf by hand to open or close the gate. Operating

the gate leaf by hand is necessary during installation

and is useful during power failures.

NSTALLING THE OPERATOR

Once you have prepared the gate, you are ready to

proceed with the installation of the operator.

Follow the instructions below to install your operator

whether in an inward or outward swinging

configuration.

Installing the operator consists of the following steps:

∗ Establishing the orientation of each gate leaf and its

operator.

∗ Attaching the rear mounting bracket

∗ Attaching the operator to the rear mounting bracket

∗ Attaching the front mounting bracket to the

operator

Page 7

January, 2004

412 Operator And

455 D Control Panel Installation Manual

Figure 4. Use the Manual Release key to disengage the

412 Operator from its motor so that you can move the

gate leaf by hand in the opening or closing direction

∗ Attaching the front mounting bracket to the gate

leaf

∗ Attaching the operator’s protective cover

∗ Installing the 455 D control panel

∗ Adjusting the torque for the operator

∗ Setting the operating controls

ESTABLISH THE ORIENTATION OF THE

PERATOR AND THE GATE LEAF

Before you begin mounting brackets or attaching parts,

you first need to establish the proper orientation of

each operator in relation to its gate leaf.

Figure 2 (page 5) shows a biparting gate from the side

where the operators are mounted. The operator

attached to the hinge on the left of the gate must be an

SX model. If the hinge is on the right side, the DX

model must be installed.

Installing the operator on the wrong side makes it

impossible to install the protective cover of the

operator.

ATTACH THE REAR MOUNTING

RACKET

Inward swinging gate:

You need to determine whether to attach the rear

mounting bracket directly to the post (or wall) or to

notch the post and install a recessed liner. Large pillars

require a recessed liner to house the rear mounting

bracket and part of the operator so that the pillar will

not interfere with the swing of the gate when it is fully

opened.

To determine whether you need a recessed liner,

measure the distances B and D (shown in Fig. 5) on your

gate. If your measure of B or D is greater than the

dimensions shown for your operator in Figure 5, notch

the post and construct a recessed liner for the post

mounting bracket (see Figure 6). The recessed liner

should be constructed of 3/16 or 1/4 in. steel with a

minimum interior height of 11 13/16 in. (30 cm) so as

to allow you to meet the required dimensions shown in

Figure 5. Make sure the recessed liner is securely

embedded in the post (or wall).

There are two parts to the rear mounting bracket. The

horizontal bracket attaches to the operator, and the

slotted vertical plate attaches to the gate post (see

Figure 8). Weld the two parts together and bolt the

assembly to the gate post of column. Note, though, that

use of the vertical rear mounting plate is optional.

Once you have positioned the rear mounting bracket,

attach the bracket to the post (or wall or recessed liner),

making sure the dimensions on your gate system match

those shown in Figure 5.

Figure 3.

Positive Stops

Remove the plug

on the top of the

motor housing

Insert the Manual Release

key and turn it in the

direction of the gate’s

closing

Looking for set up program for 455A control board to FAAC 760 dual gate
Submitted on 9-7-2023 at 01:41
Reply Report abuse

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of FAAC 455 in the language / languages: English as an attachment in your email.

The manual is 0,82 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of FAAC 455

FAAC 455 User Manual - Dutch - 12 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

FAAC 455 Manual

Product: