696306
36
Zoom out
Zoom in
Previous page
1/40
Next page
36 ENGLISH
* on models with this function.
no flaMe
The pellet feed-box is empty.
No pellet feed.
The motor reducer does not feed pellets.
Check for the presence of pellets in the feed-box.
Adjust the pellet ow (see “Easy Set Up”).
all DepR
The door is not closed correctly.
The ash drawer is not closed correctly.
The combustion chamber is dirty.
The ue exhaust pipe is blocked/dirty
Check hermetic door closure.
Check hermetic closure of the ash drawer.
Check cleanliness of the fumes pipe and the combustion chamber.
H2o oveRTeMpeRa-
TuRe
Air in the system
Inadequate circulation
Possible air in the system; bleed the system. Lack of adequate circulation.
Lack of or inadequate safety zone.
The water in the stove has exceeded 95°C.
Possible pump anomaly.
If the problem persists, restore operations must be performed by an
authorised technician.
Min H20 pRessuRe
alaRM
The system pressure read by the pressure switch
is too low.
Possible air in the system; bleed the system. Possible lack of water or leaks
due to anomalies in some system component.
If the problem persists, contact the after-sales centre
H2o pRobe
H2O probe failure Contact after-sales centre
MaX H20 pRessuRe
alaRM
The pressure of the water has exceeded the max
threshold
Possible air in the system; bleed the system. Check that the expansion
vessels are not damaged or under-dimensioned Check that the cold system
is loaded at the correct pressure
If the problem persists, contact the after-sales centre
* pRessuRe sensoR
DaMaGeD
Pressure dierential sensor faulty, disconnected
or failure.
Contact after-sales centre
* auGeR conTRol
Abnormal pellet loading. Contact after-sales centre
* auGeR block
Abnormal operation of pellet motor. Contact after-sales centre
* boileR pRobe
Boiler probe failure. Contact after-sales centre
* buffeR Tank pRobe
Buer tank probe fault. Contact after-sales centre
* Tank eMpTy
The pellet feed-box is empty.
Check for the presence of pellets in the feed-box.
Contact after-sales centre
pWM inTeRface
alaRM
IPWM output interface damaged, in short
circuit or not connected
Contact after-sales centre
HoT pWM alaRM
The pump is operating but not with good
performance. Undervoltage 160-194v.
Pump in circuit breaker protection mode.
Contact after-sales centre
sToppeD pWM alaRM
The pump has stopped but is still operational.
Undervoltage < 160v. Overvoltage.
Unexpected external ow.
Contact after-sales centre
sToppeD 2 pWM
alaRM
The pump has stopped but is still operational.
Problem in a component dierent to the pump.
Debris in installation.
Positioning in high temperature.
Contact after-sales centre
blockeD pWM alaRM
The pump has stopped permanently.
Pump blocked. Electronic module damaged
Contact after-sales centre
floW pWM alaRM
Pump blocked.
Liquid with high density.
Pipe obstructed.
Contact after-sales centre
aiR floW MeTeR
faulT
Component disconnected or faulty Contact after-sales centre
clean cHeck up 1 - 2
(1* = sTaRT-up pHase)
(2= WoRk pHase)
The bottom of the burning pot or the
combustion chamber are dirty.
The door is not closed correctly.
The ash drawer is not closed correctly.
The depression sensor is faulty.
The flue exhaust pipe is blocked
incorrect installation
Check that the holes at the bottom of the burning pot are completely free.
Check the cleanliness of the fumes pipe and the combustion chamber.
Check hermetic door closure.
Check hermetic closure of the ash drawer.
Other restoration operations must be performed by an authorised
technician.
TO FIND OUT WHERE YOUR NEAREST SERVICE CENTRE IS, CONTACT YOUR DEALER OR GO TO THE WEBSITE WWW.LANORDICA-EXTRAFLAME.COM
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame Comfort Idro L80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame Comfort Idro L80 in the language / languages: English as an attachment in your email.

The manual is 5,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame Comfort Idro L80

Extraflame Comfort Idro L80 User Manual - German - 40 pages

Extraflame Comfort Idro L80 User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info