696306
35
Zoom out
Zoom in
Previous page
1/40
Next page
35ENGLISH
Displays
Display Reason
off
Generator
o
sTaRT
The start-up phase is in progress
pelleT feeDinG
Continuous pellet feeding is in progress during the ignition phase
iGniTion
The ignition phase is in progress
pRepaRaTion
The preparation phase is in progress
WoRk
The normal work phase is in progress
MoDulaTion
The
generator
is working at minimum
final cleaninG
The nal cleaning is in progress
sTanD-by
Generator o waiting for re-ignition due to an external thermostat
WaiTinG
coolinG WaiT
A new ignition is attempted when the generator has just been switched o. When the generator switches o, one must wait for
the complete shutdown of the fumes motor, then clean the burn pot. The generator can only be re-ignited when these operations
have been
performed
.
Hoff
Generator o due to water temperature over set
*T-aMb
Display the ambient temperature (in models with this function)
*T - off
Generator o waiting for re-ignition due to all requests met
WaiTinG
black ouT
The generator
is cooling after a power cut.
Once cooling is completed it will re-start automatically
anTi-fReezinG
The anti-freeze function is in progress as the H2O t is below the factory set threshold
the pump is active until the water reaches the pre-set factory parameter +2°C
anTi-block
The pump antilock function is in progress (only if the generator has been in an OFF state for at least 96 hours); the pump is
activated for the time pre-set by the manufacturer, in order to prevent it from blocking
bloW
The automatic blow is active
He clean block
The automatic cleaning of the springs has stopped abnormally: motor blocked/damaged
alaRMs
Display eXplanaTion soluTion
Indicates the presence of an alarm.
On: indicates the presence of an alarm.
Flashing: indicates the deactivation of the depression sensor
The alarm can be reset only if the fumes motor has stopped and 15 minutes have
passed since the alarm was displayed, by pressing the key 1/
for 3 seconds.
aspiRaToR
faulT
Fumes motor fault Contact after-sales centre
fuMes pRobe
Fumes probe failure. Contact after-sales centre
HoT fuMes
High exhaust temperature
Check pellet feed (see “Easy Set Up”). If the problem cannot be solved,
contact an authorised technician.
no
iGniTion
The pellet feed-box is empty.
Pellet feed calibration inadequate.
Thermostat bulbs tripped
Check for the presence of pellets in the feed-box.
Adjust the pellet ow (see “Easy Set Up”).
Check the procedures described in the “Ignition” chapter.
Check the thermostats with bulbs (see chapter on resetting)
black ouT no iGniTion
black ouT
No current during the ignition phase.
Take the stove to OFFconditions using key 1 and repeat the procedure
described in the "Ignition" chapter.
* on models with this function.
TO FIND OUT WHERE YOUR NEAREST SERVICE CENTRE IS, CONTACT YOUR DEALER OR GO TO THE WEBSITE WWW.LANORDICA-EXTRAFLAME.COM
35


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Extraflame Comfort Idro L80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Extraflame Comfort Idro L80 in the language / languages: English as an attachment in your email.

The manual is 5,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Extraflame Comfort Idro L80

Extraflame Comfort Idro L80 User Manual - German - 40 pages

Extraflame Comfort Idro L80 User Manual - French - 40 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info