642849

Exquisit WA 6012 A plus Manual

39
Zoom out
Zoom in
Previous page
1/64
Next page
39
EN
Time assignment of the delayed washing start is performed after the symbol a has been se-
lected on the display. Maximal period of washing start delay of 24 hours (“24:H”) appears in zone F
in accordance with Fig. 3. The time is changed gradually at interval of 1 hour (“1:Н”) by turning the Knob
clockwise or contraclockwise.
If the time of washing start delay is not assigned, washing will start after button (START/PAUSE) pushing.
CHANGING SELECTED PARAMETERS
To change previously selected parameters, proceed, if needed, as follows:
– push button
R
and hold it for a 3 s;
– while pressing the Knob, select the parameter, and then assign desired value by Knob’s;
– press the Knob to latchup the selected parameter.
RETAINING PARAMETERS IN MACHINE’S MEMORY
Selected parameters can be retained in machine’s memory prior to СТАРТ/ПАУЗА (START/PAUSE)
button pushing.
Four memory sections are provided in the Machine: one for every fabric type (cotton, synthetics,
sensitive fabrics, and wool).
To retain parameters of washing proceed as follows:
– select the program and all the desired parameters of washing;
– push button
«
and exit from selection mode; push button .
Previously retained parameters will be highlighted when next program is selected. These parameters
can be changed.
DOOR BLOCKING AGAINST CLOSING
It is provided to prevent accidental powering on the Machine by kids. To block the door against closing,
turn the sleeve in accordance with Fig. 4 with screwdriver clockwise up to the stop. The sleeve will come
forward not allowing the door to be closed. To remove the blocking, prior washing start, perform the acts
in reverse sequence.
3 PRELIMINARY STARTING PROCEDURE
PREPARING TO INSTALLATION
CAUTION! To prevent the Machine from being damaged not, move it by grasping at the dispenser
drawer, door, or gasket in accordance with Fig. 1
For transportation purposes, the drum of the Machine is fixed by locking bolts and spacer bars.
Unscrew the four bolts with a spanner and take out the spacer bars (Fig. 5). If the spacer bars remain
inside the Machine and would not get out, remove the back panel (Fig. 6) with a cross-blade screwdriver
and take the bars out. Reinstall the panel. Close the holes with plastic plugs, if they are supplied. Keep the
bolts and spacer bars for future transportation.
NEVER operate the Machine with open spacer bar holes in the rear wall of the body.
CAUTION! To avoid potential body damage, don’t switch on the Machine not removing locking
bolts and spacer bars previously.
INSTALLING THE MACHINE
The Machine should be installed on a solid, even and dry surface. Soft flooring (carpets, polyurethane-ba-
sed coatings etc.) is not recommended as it promotes vibration and degrades ventilation of the Machine.
When installed on a wooded floor, the Machine should be first placed onto a wooden slab at least 15
mm thick that is reliably bolted to the floor. To increase the stability of the Machine during its operation on
Figure
5
support
locknut
Figure 6
Figure
4 Figure 7
sleeve
door panel
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Exquisit WA 6012 A plus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Exquisit WA 6012 A plus in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info