Manual Expobar Brewtus II (page 5 of 12) (English)

499723

Zoom out

Zoom in

1/12

Bella Barista

Nene Court, The Embankment,Wellingborough, Northants, NN8 1LD

Tel: 01933 273275

e-mail: claudettep@towability.com

Preparing the machine for use

Peel off any protective film, ensure the water source lever (tank or mains) is in the correct

position (for the test machine this was the opposite way to that stated in the Expobar manual),

lift the machine onto the counter, wash the cold water tank, fill it with filtered water. Don’t

forget to snip the little cable tied at the bottom far edge of the water tank platform (unless you

have plumbed it in), you have to remove the tank to do this. If you don’t the machine will not

switch off when the water runs low

I never like the idea of using a machine without thoroughly flushing it through, especially

considering that the machine may have stale water from factory testing (many months old), or

manufacturing residues, Because of the design, I was inclined to put about 3 tankfulls of

water through it.

Key features

Item/Description Picture Comments

The little pipe behind the group vent. This

is for venting water from the pump OPV

valve (over pressure valve) when pulling

a shot. As the machines only form of

pressure regulation a little water comes

out on every shot. It unfortunately isn’t

long enough to be over the hole in the

drain rack over the drip tray so you get a

pool of water forming on the top drain

rack. Solved by cutting about 30 mm off

water inlet pipe in the tank (of which there

is plenty), placing that on the pipe and

routing it into the drip tray as shown

This really should be fixed, it

cannot be that hard to do and

Expobar should address this.

You have two solutions,

either do as I have done in

the picture or purchase a

piece of Teflon pipe and

route it back into the water

tank, from behind the panel

(most other coffee machines

vent OPV runoff back to the

tank).

Some minor rattles from the drain rack

and cup tray

This could easily be solved by the addition of some spring

tabs on the drain rack which would press on the inner walls of

the drip tray. Rattles are fairly easy to solve with a little foam

tape.

High pressure pump lines were simple

high pressure plastic tubing not the steel

braided pipes seen in some machines

The steel braided high pressure line on

the Zaffiro

I don’t expect it will cause a

problem, It is just an

observation. No doubt

braided pipe would have

added to the cost, with little if

any impact on reliability.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Expobar Brewtus II in the language / languages: English as an attachment in your email.

The manual is 0,92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Expobar Brewtus II Manual

Product: