798844
8
Zoom out
Zoom in
Previous page
1/13
Next page
1514 Assembly, Operation & Maintenance InstructionsAssembly, Operation & Maintenance Instructions
STEP 02
/ If not already assembled, lever up the element and place the heat shield (09) inside the bowl.
Take the two element supports (08), t them together and place them centrally on the heat
shield. Lever the element back down onto the element supports.*
STEP 03
/ Place the charcoal chamber (07) centrally within the barbeque (it will allocate on four tabs) and
place the charcoal grid (06) in the centre hole above the element.
STEP 04
/ Place the grill (hinges down) on the eight pins inside the chassis, above the charcoal chamber.
STEP 05
/ The rotisserie rod and Cliplock ForksTM are stored in the compartment at the front of the left
hand side panel. Lift the storage door up, remove the Cliplock Forks™ (11) (take care of the
sharp points of the fork ngers) and pull the rotisserie rod (10) out from the storage bracket.
Note: If the barbeque has been in operation, the rotisserie parts may be hot – remove before
cooking or use heat proof gloves. The handle of the rotisserie rod must rst be extended by
rotating the handle anti-clockwise until the thread releases, extending the handle fully and
tightening in place by rotating anti-clockwise again. The Cliplock Forks™ slide on the rod and are
locked in place by pressing down on the fork levers.
STEP 06
/ To extend the rotisserie poles, rst press and release them so the rst section pops out from
the barbeque. Pull the poles up and rotate clockwise to allocate the poles in one of the 3 height
settings. The pole to the right contains the rotisserie motor.
STEP 07
/ Take the rotisserie rod with the food attached and place the pointed end in the motor hole at
the top of the right hand side pole. Lever the handle side of the rod down into the slot of the
left hand pole (take care the slot in the rod allocates to the keyway) and close the pole cover.
STEP 08
/ Place the pedestal base cover (S04) face down on a at, clean surface and place the pedestal
base (S05) inside. If not already tted, attach the six rubber feet (F07) onto the pedestal base
with six M3x10mm screws (F05). Place the pedestal support bracket (S06) onto the bottom of
the pedestal base (centred on the pole hole). Align the four outer holes and x together using
four M4x8mm screws (F06). Tighten fully.
STEP 09
/ Place the pole support on top of the pedestal base (centred on the pole hole). Centre over the
pole hole and align the 4 central holes. Fix together using four M8x25mm screws. Tighten fully.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Everdure Fusion at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Everdure Fusion in the language / languages: English as an attachment in your email.

The manual is 4.68 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info