798845
8
Zoom out
Zoom in
Previous page
1/13
Next page
1514 Assembly, Operation & Maintenance InstructionsAssembly, Operation & Maintenance Instructions
STEP 01
/ The hood and barbeque chassis assembly is transported screwed to the stand top by
four M6x20mm screws and four Ø6mm spring washers (two at the front and two at the
rear). Before attempting to build the stand, the stand top should be removed.
Angle the assembly slightly to the back and remove both M6x20mm screws, then do the
same at the front, supporting the parts so they don’t drop. Keep all of the fasteners for
later use. Removable stickers at the front and rear will mark the positions of these screws.
Remove the hood and barbeque chassis assembly from the stand top and place on the
ground.
STEP 02
/ Take the stand top (01B) and place it upside down (leg stumps up) on a clean surface
(note: there is no front or rear to this part). Take the right front leg (04 with a screw hole
in the foot) and slot it over the rear right corner stump. Fix in place using a M6 x 12mm
screw (A) and spring washer (D), but do not tighten. Take the right rear leg (05 with a
screw hole in the foot) and slot it over the front right corner stump. Fix in place using a
M6 x 12mm screw (A) and spring washer (D), but do not tighten.
Take the left front leg (02) and slot it over the rear left leg stump. Fix into place using a
M6x12mm screw (A) and spring washer (D), but do not tighten. Take the left rear leg (03)
and slot it over the front right leg stump. Fix into place using a M6x12mm screw (A) and
spring washer (D), but do not tighten.
STEP 03
/ Take the two bottom shelf supports (06) and t them onto the cylindrical tabs at the
inside of each foot. Rotate each one so that the outmost screw holes are facing inwards
and the inner screw holes are facing the stand top (if not, pull out and t in the opposite
way). Fix in place with four M6x12mm screws (A) and spring washers (D). When all are
assembled, tighten up all four screws and the screws from step 02.
STEP 04
/There are two threaded holes at the inside of the right hand legs. Take the support chain
(15) and x it to the two legs with two M6x12mm screws (A). Tighten fully.
STEP 05
/ Turn the stand onto its legs and check that all of the legs are stable. Take the plastic
bottom shelf (07) and place it on the two bottom shelf supports. Line the four holes in
the bottom shelf up with the threaded holes in the bottom tray supports and x into
position using four M5x12mm screws (B) and four spring washers (E). Tighten fully.
STEP 06
/ Push the at edge of the cylinder hook (14) into the slot of the stand top (above the
right hand side legs and castors) up until the dogleg, and then rotate down until the hook
is against the stand top side. Fix into place using a M6x12mm screw (A), M6 locking nut
(C) and spring washer (D). The stand is now complete.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Everdure Force at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Everdure Force in the language / languages: English as an attachment in your email.

The manual is 6.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info