798845
4
Zoom out
Zoom in
Previous page
1/13
Next page
76 Assembly, Operation & Maintenance InstructionsAssembly, Operation & Maintenance Instructions
APPLIANCE DETAILS
Barbeque FORCETM FURNACETM
Gas Type ULPG N.G ULPG N.G
Burner Pressure 2.75 kPa 1.0 kPa 2.75 kPa 1.0 kPa
Injector Diameter: Ø0.95 mm Ø1.60 mm Ø0.85 mm Ø1.45 mm
Heat Input: 23 MJ/ hr 23 MJ/ hr 29.1 MJ/ hr 29.1 MJ/ hr
Note: The size of the injector diameter is stamped on one of the hexagon faces (e.g. ‘165’ for
Ø1.65mm injector).
Barbeque FORCETM FURNACETM
Barbeque only LENGTH
(mm)
WIDTH
(mm)
HEIGHT
(mm)
LENGTH
(mm)
WIDTH
(mm)
HEIGHT
(mm)
1170 515 410 1310 515 410
Barbeque and
stand
1170 750 1170 1310 750 1170
Air is admitted at the underside of the combustion chamber (two 35mm x 20mm gaps
between the fat tray and the chamber through an oval hole 75mm x 135mm in size).
Exhaust gases are emitted around the edge of the plates (6mm gap) and through a
275mm x 40mm slot in the rear of the hood. When using an open grill, aeration also takes
place through the slots of the grill.
GAS CONNECTIONS
LOCAL AUTHORITY REQUIREMENTS
Check Gas Type and speci cations plate on the underside of the right-hand servery. All
gas  tting work, service and repairs can only be performed by an authorised person in
accordance with AS5601 and local gas regulations. Hose connections are G1/2-14 for
ULPG & NG
NATURAL GAS
FORCETM & FURNACETM barbeques can be converted to use natural gas ONLY with
a FORCETM & FURNACETM NG conversion kit. Fit the NG injector (into the valve),
regulator and NG hose following the supplied instructions. Conversion of any barbeque
from ULPG to NG (or vice versa) must be done by a licensed gas  tter/technician. Refer
to AS5601 for piping sizes. Please contact Everdure by Heston Blumenthal for further
information.
FOR ULPG CYLINDER CONNECTION
1. To achieve the optimum performance from your barbeque, an approved gas cylinder
(POL  tting) of 4kg or 9kg capacity must be used. Take care to keep the hose away
from the hot barbeque.
2. Do not connect gas to a barbeque that is not secured in the supplied stand or on a
stable raised surface. The cylinder must be placed on the cylinder support hook at the
right hand side of the stand when one is used. The cylinder should be lower than the
barbeque & in a protected place when not using the stand.
3. Connect the cylinder to the barbeque, via the hose and regulator. Firmly tighten joints,
but do not over-tighten. Take care not to damage the regulator  tting. Check that the
gas control knob/valve is in the O position before opening the gas cylinder.
NOTE: Only one gas cylinder should be stored on the stand at any one time.
LEAK TESTING
1. Make sure the gas control knob is O and turn the cylinder valve On.
2. Check for leaking joints by brushing with solution of half-liquid detergent and half water.
If a leak is present, bubbles will appear (or you may hear a hissing sound). Retightening
connections can generally repair a leaking joint. You must also check the gas hose and
connection at the gas cylinder. If a leak cannot be resolved, do not proceed.
OUTDOOR INSTALLATION GUIDE
This Appliance shall only be used in an above ground open-air situation with natural
ventilation, without stagnant areas, where gas leakage and products of combustion are
rapidly dispersed by wind and natural convection.
This appliance must not be used indoors. Do not use your barbeque in garages,
porches, sheds or other enclosed areas. The barbeque is not intended to be installed in
or used on recreational vehicles (e.g. boats, camping vans) and should not be placed
close to or under any surfaces that will burn or are sensitive to heat. Do not block/
obstruct the  ow of air and combustion around the barbeque housing while in use.
Any enclosure in which the appliance is used shall comply with one of the following:
An enclosure with walls on all sides, but at least one permanent opening at ground level
and no overhead cover.
Within a partial enclosure that includes an overhead cover and no more than two walls
Within a partial enclosure that includes an overhead cover and more than two walls, the
following shall apply-
(i) at least 25% of the total wall area is completely open: and
(ii) at least 30% of the remaining wall area is open and unrestricted.
In the case of balconies, at least 20% of the total of the side, back and front wall areas
shall be and remain open and unrestricted.
Open side at
least 25% of
total wall area
least 25% of
total wall area
Open side at
least 25% of
total wall area 30% or more in total of
the remaining wall area is
open and unrestricted
Both ends open
Open side at
least 25% of
total wall area
30% or more in the total of the
remaining wall area is open and
unrestricted.
DO NOT USE NAKED FLAME FOR LOCATING GAS LEAKS.
IF A LEAK PERSISTS CALL AN AUTHORISED GAS FITTER.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Everdure Force at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Everdure Force in the language / languages: English as an attachment in your email.

The manual is 6.19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info