Approaching the water set, the stove goes into modulation and when the set is passed, the stove goes into modulation and then stand-by.
Below water set the stove comes on again and resumes operation.
The stove in no way considers the temperature measured by the ambient sensor of the same stove.
Water takes priority.
Mode 3
WITH RESPECT TO THE THERMOSTAT AND TO THE TEMPERATURE OF THE WATER.
Having set the water temperature, commence operation of the stove.
1- With the thermostat open the stove goes into modulation and then stand-by.
2- With the thermostat closed the stove is working.
Nearing Set Water, the stove goes into modulation and remains in modulation. It only goes into stand by mode when the thermostat opens the contact. It turns
on when the thermostat closes the contact.
The stove in no way considers the temperature measured by the ambient sensor of the same stove.
The thermostat takes priority.
Menu 05 – BUZZER MODE:
Set it to “OFF” to disable the buzzer.
Menu 06 – ENABLE FAN:
The heating stoves with built-in room fan have this menu. With this menu it is possible to enable or disable the room fan. The fan power is pre-set according to the
operating power of the stove.
Menu 07 – INITIAL LOAD
This function is important if the stove is new or if the stove is off due to the absence of pellets in the hopper.
INITIAL IGNITION MUST BE PERFORMED BY AUTHORISED PERSONNEL ONLY, NOT BY THE PURCHASER.
CONTACT THE SERVICE CENTRE THAT WILL SEND OUT A SPECIALIST TECHNICIAN.
Use this function to load pellets for a period of 90 seconds when the stove is switched off and cold. Start with button P1 and stop with button P4.
Menu 08 – STOVE STATUS:
This function displays the current status of all the devices connected to the stove. A few examples are included in the following pages.
08.3 USER FUNCTIONS
Standard functioning of a control board properly installed on a forced air pellet stove is described below with reference to the functions available to users. The
indications listed below refer to a control board fitted with programmable chrono-thermostat.
Stove ignition
Ensure that there are pellets in the hopper, that the burn pot is correctly positioned and free from any combustion residues and then close the door.
To turn on the stove, press button P4 for a few seconds. The display shows that the stove is on.
Start-up phase
The stove performs all the steps of the start-up phase according to the parameters concerning its levels and times. The display will show the wording ON, as there
is no pellet loading but the exhaust blower is in operation. PELLET LOADING state will occur where the pellets are being loaded into the burn pot. Once the pellets
have started to burn and the fume temperature is increased, the display will show FIRE ON, a transition phase between ignition and operating power.
Ignition fault
After the Pr01 time has elapsed, if the flue gas temperature has not reached the minimum permitted value, parameter Pr13, reached with the power of 2°C/min,
the stove goes into alarm status.
If there are unburned pellets inside the burn pot, it is necessary to empty the burn put before switching on the stove. Pellet waste and potential bursting inside the
combustion chamber will thus be avoided.
If the pellets have started to burn but the FAILED IGNITION alarm status persists, it is necessary to wait for all the pellets to burn and then to re-ignite.
Check that there are pellets inside the hopper.
Stove operational
Once the start-up phase is completed, the stove switches to work mode which represents the normal operating mode.
If the stove temperature is the same as the set power, the pump starts.
Changing set room temperature
To change the room temperature, simply press the P2 button. The display shows the current SET temperature value.
Changing the temperature setting of the heating stove
To change the room temperature, simply press the P1 button. The display shows the current SET temperature value.
External thermostat/chrono-thermostat use
If you want to use an external programmable thermostat, connect it to the TERM clamps (connector CN7 pin 7-8).
External thermostat
External chrono-thermostat
The stove external thermostat is enabled when the contact is closed with stove on.
Room temperature reaches the set value (SET temperature)
When the set room temperature value is reached or the fume temperature has reached the Pr13 value, the stove heat output is set automatically to the minimum
value, MODULATION mode.
If the stove is in the STAND-BY mode, it switches off after the period of time set by Pr44 and after reaching the SET temperature.
Restart occurs after the following condition has occurred: Tambient > (TSET + Pr43)
The same situation is obtained when the heating stove temperature reaches the same level as that set. The modulation status is evident and, if enabled, STANDBY
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Eva Calor Sola at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Eva Calor Sola in the language / languages: English as an attachment in your email.
The manual is 4.77 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
