3. Meaning of pictograms
1. Caution – rotating tool
2. Caution – refer to the operating instructions
4. Technical data
Engine 4-stroke
Engine rating 3 kW / 4.1 bhp
Working width 36 cm
Cultivating blade set/diameter 2 sets L+R / 26 cm
Forward gears 1
Starting system Reversing device
Fuel Unleaded standard grade petrol
Engine oil Approx. 0.6 liters
5. To assemble the power cultivator
앬Secure the handle bracket (2) as shown in Figure 3.
The Bowden cable (B) for the clutch must be posi-
tioned on the top of the rear of the bracket (Figure
4). The height of the handle bracket (Figure 9) can
be adjusted using the screws (A).
앬To give the machine better stability, insert the
depth stop (5) straight away and secure it with the
split pin (6) (Figure 11).
앬Attach the Bowden cable (B) to the top hole in the
clutch lever (I) as shown in Figure 7.
앬Undo the hexagonal nut (G) on the Bowden cable
adjusting screw and insert the adjusting screw into
the mounting loop (H) and secure it with a hexago-
nal nut (G) (Figure 8). The adjusting screw should
be at the rear of the thread and should not be furt-
her forward than the middle. If the clutch lever (I) is
pressed down fully when the engine is running, the
cultivator blades should turn. If the cultivator bla-
des do not turn properly, it means that the engine
mounting has not been tensioned tightly enough
against the V-belt and in this case the adjusting
screw (X) can be undone further in the direction
indicated by the arrow (Figure 8). This creates grea-
ter tension on the V-belt.
앬Secure the Bowden cable tube from the accelerator
lever to the machine frame using the cable ties (4),
Figure 5.
6. To start the machine
앬For safety reasons the machine is delivered without
any petrol or engine oil inside it.
앬First add the oil. Unscrew the oil dipstick (J) from
the oil filler neck and fill the oil sump with engine
oil grade 10W40 (approx. 0.6 liters) until the level
reaches the “max” mark on the dipstick (J) (Figure
12).
앬Fill the petrol tank with standard grade unleaded
petrol.
앬Set the depth top (5) to the correct height and
secure it with the split pin (Figure 11).
앬Swing the transport wheel upwards and engage it
with the spring (Figure 10).
앬Set the petrol cock (F) to “ON” (Figure 6).
앬Set the starter lever to position –a- (Figure 13).
앬Pull the starting cable gently until you feel resi-
stance then pull it hard. If the engine does not start
straight away, repeat the starting routine.
앬Starting lever in position -b- = Idling
앬Starting lever in position -c- = Stop engine
앬You can adjust the complete handle bracket to suit
your body size. To do this undo the screws
-A- in Figure 9, adjust the bracket and tighten the
screws again.
앬To start work, push the starting lever further in
direction -a- to suit the soil conditions.
앬To start the cultivator blades, simply push the
clutch lever (I) downwards and hold it there (Figure
7). When you release the clutch lever the cultivator
blades will stop.
7. Servicing
앬Only use genuine spare parts.
앬Dispose of oil and petrol in the places provided for
them.
앬Spare spark plugs:
For example Bosch WR 7DC or Denso W16EPR-U
8. Ordering replacement parts
Please quote the following details when ordering repla-
cement parts:
앬Type of machine
앬Article number of the machine
앬Serial number of the machine
앬Replacement part number of the part you require
(Refer to the replacement parts list)
For our latest prices and information please go to
www.isc-gmbh.info
13
GB
