783788
23
Zoom out
Zoom in
Previous page
1/24
Next page
42 43
- You are using a 2.4GHz router or a dual-band router that is configured to support a
2.4GHz frequency band. RoboVac does not support 5GHz frequency band.
- If RoboVac cannot connect to the Wi-Fi network and you are using a 2.4/5GHz
mixed network, switch to a 2.4GHz network for Wi-Fi setup. You can switch back
once your setup is complete.
- When connecting to a hidden network, make sure you enter the correct network
name, SSID (case sensitive), and connecting to a 2.4GHz wireless network.
- When using a network extender/repeater, make sure the network name (SSID)
and password are the same as your primary network.
- The firewall and port settings of your Wi-Fi router allow RoboVac to connect with
the Eufy servers.
Network Security Requirement
- WPA and WPA2 using TKIP, PSK, AES/CCMP encryption.
Wi-Fi Channels
- The FCC requires that all wireless devices in the United States operate on the 1-11
wireless spectrum channels.
- Some countries outside North America can use spectrum channels higher than
channel 11. Refer to your local regulatory agency to determine which channels are
accessible.
- A future software release will support access to channels above 11 for users
outside North America. Until then, use channels 1-11.
If you cannot control RoboVac with your smartphone, try the solutions below to solve
the problem. If the problem persists, contact the Eufy service center for help.
Wi-Fi Status
Light Cause Solutions
Solid blue
RoboVac has connected
to your router, but
cannot access the
Internet.
• Check if your router is connected to the
Internet.
• Check with your Internet provider to
see if there is any Internet connection
problem.
Rapidly
flashing blue
RoboVac cannot
connect to your
wireless router.
• Check if you have modified your network
name and password.
• Reset Wi-Fi connection if necessary.
Refer to the “Use Your RoboVac with
the EufyHome App > Restore Factory
Settings” section in this manual.
Slowly
flashing blue
Wi-Fi connection is
reset or has not been
set up before.
• Set up Wi-Fi connection with RoboVac.
Refer to the “Use Your RoboVac with
the EufyHome App” section in this
manual.
• Reset Wi-Fi connection if necessary.
Refer to the “Use Your RoboVac with
the EufyHome App > Restore Factory
Settings” section in this manual.
Wi-Fi Status
Light Cause Solutions
Off
• RoboVac is turned off.
• RoboVac’s power
level is low.
• RoboVac is in Sleep
mode.
• Charge RoboVac by attaching it to the
Charging Base. Make sure the main
power switch on the bottom of RoboVac
is turned on.
Specifications
Input 19 V 0.6 A
Battery Voltage 14.4 V
Power Consumption 40 W
Battery Type 14.4 V
Li-ion 2600 mAh
Dust Collector Capacity
450 ml
Water Tank Capacity 130 ml
Charging Time 300 - 360 mins
Input 19 V 0.6 A
Output 19 V 0.6 A
Customer Service
For FAQs and more information, please visit www.eufylife.com.
Email: support@eufylife.com
Live Chat: www.eufylife.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eufy T2151 - RoboVac G10 Hybrid at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eufy T2151 - RoboVac G10 Hybrid in the language / languages: English as an attachment in your email.

The manual is 2.82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Eufy T2151 - RoboVac G10 Hybrid

Eufy T2151 - RoboVac G10 Hybrid User Manual - German - 20 pages

Eufy T2151 - RoboVac G10 Hybrid User Manual - Dutch - 20 pages

Eufy T2151 - RoboVac G10 Hybrid User Manual - French - 20 pages

Eufy T2151 - RoboVac G10 Hybrid User Manual - Italian - 20 pages

Eufy T2151 - RoboVac G10 Hybrid User Manual - Spanish - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info