807583

Eufab 21076 - AC010313D Manual

9
Zoom out
Zoom in
Previous page
1/24
Next page
9
The units are converted as follows:
1 psi = 0.069 bar 1 bar = 14.504 psi
6.2.3 CONVERSION TABLE PSI / BAR
Table 1
Table 2
Rotate the tip (Position 17 in Figure 9) of the 12 V plug
(Position 15 in Figure 9) anti-clockwise until it comes away
from the plug and then remove. The fuse (Position 16 in
Figure 9) is exposed and can be removed from the plug.
Replace the fuse with another of the same strength and screw
the tip back into the plug, Figure 9.
6.3 REPLACING THE FUSES
6.3.1 REPLACING THE FUSE FOR THE 12 V SYSTEM
Figure 9: Fuse in 12 V plug
psi
bar
psi
bar
10
0,7
70
4,8
20
1,4
80
5,5
30
2,1
90
6,2
40
2,8
100
6,9
50
3,4
110
7,6
60
4,1
120
8,3
bar
psi
0,5
7
1,0
15
1,5
22
2,0
29
2,5
36
3,0
44
Open the storage compartment lid on the rear of the device.
Remove the connection cable and the air hose. See also Figu-
re 3 in the overview. Rotate the end cap (Position 18 in Figure
10) and remove. Remove the fuse (Position 19 in Figure 10)
from the holder (Position 20 in Figure 10). Replace it with a
new fuse of the same strength. Rotate the end cap back into
the holder.
6.3.2 REPLACING THE FUSE FOR THE 230 V SYSTEM
Figure 10: 230 V fuse in storage compartment
6.4 TROUBLESHOOTING
ERROR The compressor is not functioning
POSSIBLE CAUSE
POSSIBLE CAUSE
POSSIBLE CAUSE
MEASURE
MEASURE
MEASURE
The connection cable is not
connected correctly.
When operating using a vehicle:
No voltage to the on-board socket.
Check the cable connection and
connect correctly.
Switch on the ignition of your
vehicle. Check the fuse for the
on-board socket and replace
if necessary.
Replace the faulty fuse, see section
6.3
The fuses in the compressor have
been triggered.
7. MAINTENANCE AND CARE
7.1 MAINTENANCE
7.2 CARE
When used according to the instructions, the Dual Power
Compressor is maintenance-free. Store the compressor in a
dry, frost-free location.
Switch the compressor o before cleaning, separate from the
power supply. Clean the housing of the compressor with a
soft, dry cloth. Do not use any aggressive cleaning agents or
solvent-based cleaners. Never allow liquids to penetrate the
housing.
8. NOTES REGARDING ENVIRONMENTAL PROTECTION
Do not dispose of electrical devices with house-
hold waste. Electrical devices and electronic
scrap must be collected separately and disposed
of in an environmentally responsible manner
for recycling. Please contact your community or
city administration regarding disposal options
for electrical and electronic scrap. The materials
are recyclable. You make an important contribu-
tion to protecting our environment by recycling,
material utilisation or other forms of reusing
waste equipment.
9. CONTACT INFORMATION
EAL GmbH
Otto-Hausmann-Ring 107
42115 Wuppertal, Germany
+49 (0)202 42 92 83 0
+49 (0) 202 42 92 83 – 160
info@eal-vertrieb.com
www.eal-vertrieb.com
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eufab 21076 - AC010313D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eufab 21076 - AC010313D in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0.91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info