806931

Eufab 11511 Manual

5
Zoom out
Zoom in
Previous page
1/12
Next page
5
4. SAFETY PRECAUTIONS
• The warning triangle labels all instructions important to
safety. Always follow these otherwise you could injure yourself or
damage the device.
• Children may not play with the device.
• Cleaning and user maintenance may not be carried out by
children without supervision.
• Do not treat packaging material carelessly. This may become a
dangerous plaything for a child!
• Only use this product for its designated purpose!
• Do not manipulate or disassemble the device!
• For your own safety, only use accessories and spare parts that
are stated in these instructions or that are recommended by the
manufacturer!
• Continue to observe the safety precautions in the instructions for
your bicycle rack.
5.OPERATING INSTRUCTIONS
5.2 INSTALLING THE EXPANSION TO THE EXISTING BICYCLE RACK
Figure 1: Screws of rack table
Figure 2: Remove the lamp mount
Undo the two hexagonal screws (Figure 1) on the underside of the rear end of the
rack table and remove fully. Put the screws to one side so that they will not be lost.
Pull the lamp mount fully out of the rack table.
5.1 PREPARATION
If you have already used your JAKE bicycle rack, you will  rst need to remove the
cable set from the bicycle rack. To do this, cut through the cable ties. You will need
8 new cable ties (not included in the scope of delivery of the expansion) to reattach
the cable set after installation. If you are  tting the expansion to a JAKE bicycle
rack that is straight from the factory, you can use the cable ties from the scope of
delivery of the bicycle rack instead.
Undo the nut and pull the carriage bolt from the attachment base of the expansion
rail (Figure 3 and 3 a).
Figure 3: Attachment base
Figure 3a: Remove the carriage bolt
Remove the  ller element and sleeve from the attachment base (Figure 4).
Fit the sleeve to the pipe of the lamp mount (Figure 5).
Figure 4: Removing the  ller element and sleeve
Figure 5: Fitting sleeves
Place the expansion rail on the sleeve (Figures 6 and 7). To do this, the closures
must face forwards in the direction of travel (Figure 8).
Figures 6 and 7:
Position the expansion rail
Figure 8:
Installation position of closures
Figures 6 and 7:
Position the expansion rail
Figures 6 and 7:
Position the expansion rail
Replace the  ller elements back in the attachment base. Fit the carriage bolt from
the outside, on the side with the square socket, into the attachment base, and  t
the washers and nuts. Do not tighten the nuts yet.
Now insert the pipes of the lamp mount back into the rack table. Slide the pipes in
far enough that the marks (Figure 9) on the pipes are just hidden.
Figure 9: Marks on the lamp mount
Screw the hexagonal screw back into the bottom of the rack table. Pay attention to
ensure that the screws go through the drilled holes in the pipes of the lamp mount.
Tighten the screws.
Now align the expansion rail, as far as possible to the back and parallel to the rear
lights. Tighten the nuts in the attachment base. Fit the protective caps (Figure 10)
onto the nuts.
Figure 10: Protective cover
Close the rear drilled holes in the pipes of the lamp mount using the end caps
(Figure 11).
Figure 11: End caps
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eufab 11511 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eufab 11511 in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0.73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info