820911
2
Zoom out
Zoom in
Previous page
1/3
Next page
2 / 3
DIP switch 4
Maximum sensitivity (default setting)
Reduced sensitivity = optional masking of interference sources
Despite careful planning and positioning, interference sources
can still cause undesired switching, such as local hot air streams
from heaters or underfloor heating; ventilators, air-conditioning
units, fans, lights, TVs and HiFis, or computers.
NB: If reducing the sensitivity does not manage to mask the
interference source completely, you can also mask out individual
areas of detectors by means of the enclosed covering clips / lens
mask. Alternatively you will need to re-position the detector.
5.3 Additional manual control by button
5.3.1 “lighting” channel
The detectors have a separate “S” terminal for connecting an external button (button –
operating current – with zero conductor connection). This means that the detector can be
manually overridden at any time so that the lighting-C1” channel can be switched on or off
individually.
Manual switch-on: The lighting will remain switched on for as long as the detector continues
to detect movement. If movement is no longer detected, the lighting will switch off and the
detector will revert to the set operating mode once the set time has elapsed.
Manual switch-off: The lighting will remain switched off for as long as the detector continues
to detect movement. If movement is no longer detected, the detector will revert to the set
operating mode once the set time has elapsed.
The button function can also be set as follows:
DIP switch 3
“Room” button function – manual switch-on and switch-off (default setting)
“Hallway” button function – manual switch-on only
Manual switch-off not possible, safety function for pathway and
hallway lighting
5.5. Control: acoustic sensor (MD-C 360i/8 MIC + PD-C 360i/8 MIC)
The acoustic sensor can only be adjusted manually using the control.
• Turning all the way to the left (-) deactivates the sensor
• Turning all the way to the right (+) maximises sensitivity
The acoustic sensor will only be enabled if the detector is activated first, either by
movement or by switching on manually (button or remote control). This stops noises from
outside the monitored area affecting operation.
Automatic switch-off: if movement or noise is no longer detected, the lighting will be
switched off once the set time has elapsed. The lighting can be immediately re-activated,
e.g. by calling out (making a noise), within 8 seconds. The acoustic sensor should be
adjusted to take into account the surrounding area (noise from nearby HiFis or TVs could
trigger the sensor, for instance). The green LED indicates the acoustic sensor’s response.
6 DISPOSAL / WARRANTY
This device must not be disposed of as unsorted residual waste. Owners are
required by law to correctly dispose of used devices. More information is
available from your local town council.
ESYLUX manufacturer's warranty at www.esylux.com. Technical and design features may
be subject to change. Technical data for products at www.esylux.com/products.
5.4 Sensitivity adjustment
DIP switch 2 Toggle between “fully automatic and semiautomatic operation”
Fully automatic mode – “lighting” switching channel – see 4.1
Semiautomatic mode – only for “lighting” switching channel
Manual switch-on: The detectors have a separate “S” terminal for
connecting an external button (button – operating current – with
zero conductor connection). This means that the detector can
be manually overridden at any time so that the lighting can be
switched on or off individually.
Automatic switch-off: If movement is no longer detected, the
lighting will be switched off once the set time has elapsed.
MD-C 360i/8
MD-C 360i/24
MD-C 360i/32
MD-C 360i/32 Corridor MD-C 360i/8 MIC
PD-C 360i/8
PD-C 360i/24
PD-C 360i/32
PD-C 360i/32 Corridor PD-C 360i/8 MIC
PD-C 360i/8 plus
PD-C 360i/24 plus
PD-C 360i/32 plus PD-C 360i/24 Dry
230 V ~ / 50 - 60 Hz
Power consumption in W 0,3 0,3 0,3 0,3 0,3 0,3
Field of detection 360°
Range (diameter in m)
8
24
32
8
8
24
32
8
8
24
32
24
Settings on device or via remote control Mobil-PDi/MDi
Light value approx. 5 lux - 2000 lux / daytime operation
“Lighting” channel
Switching capacity: 2300 W / 10 A (cos φ = 1),
1150 VA / 5 A (cos φ = 0.5), capacitive load / electronic
ballasts *
Switching capacity: floating / NC, 230 V ~ / 5 A,
24 V / 5 A, capacitive load / electronic ballasts * 2x
In-built acoustic sensor
Time setting: impulse / 1 min. - 30 min.
Switch input – lighting
“HVAC” channel
Switching capacity: floating / NO, 230 V ~ / 2 A,
24 V / 2 A, capacitive load / electronic ballasts *
Time setting: impulse / 5 min. - 120 min.
Slave connection: PD-C 360/8 Slave, PD-C 360/24 Slave,
PD-C 360/32 Slave
Protection type: recessed-mounted IP 20,
IP 20 / IP 54 with surface-mounted box (accessory),
ceiling-mounted IP 20 (accessory)
Protection class II II II II II II
Operating temperature range -25 °C ... +50 °C
Colour: white, similar to RAL 9010
* inrush limiter required
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Esylux MD-C serie at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Esylux MD-C serie in the language / languages: English as an attachment in your email.

The manual is 0.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Esylux MD-C serie

Esylux MD-C serie User Manual - German - 3 pages

Esylux MD-C serie User Manual - Dutch - 35 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info