700196

ESX SXE1200.1D Manual

11
Zoom out
Zoom in
Previous page
1/40
Next page
11
INPUT SENSITIVITY
TurntheLEVELINPUT(Fig.1,7)controlleroftheampliertotheMINposition.Thenturnthevolumecontroller
of the head unit to 80 - 90% of its full setting. Now turn LEVEL INPUT clockwise until you hear some distortion.
Then turn back the LEVEL INPUT slightly until you hear a cleaner sound.
VARIABLE BASS BOOST
By using the BASS BOOST controller (Fig. 1,3) you are able to increase the bass enhancement from 0 to 12
dB. ATTENTION: Use the BASS BOOST wisely!
HIGH LEVEL INPUTS & AUTO TURN ON
The high level inputs under HI INPUT (Fig. 6) is suitable to connect the device input with speaker wires, if your
headunitisnotequippedwithpre-amplierRCAoutputs.Extendthereforeveryregardingspeakercablefrom
your head unit with appropriate speaker cables from your car audio retailer to the mounting location of the am-
plier.ThenconnecttheeachmatchingloudspeakercablewiththecablesoftheincludedHighLevelInputjack.
CAUTION: Never use the high level inputs and the RCA inputs at the same time. This may damage the
device seriously.
Theamplierdetectsavoltagerise(6Volts)withasocalled”DCOffset”overtheconnectedinputsignalonthe
highlevelinputsunderHIINPUT(Fig.6)whentheheadunitwillbeswitchedon.Hence,theamplierwillalso
beturnedon.Assoonastheheadunitwillbeturnedoff,theamplierturnsalsoautomaticallyoff.Inthiscase
the turn-on connection REM (Fig. 2,2) is not needed.
NOTE: The Auto Turn On function usually works with 90% of all head units, because they are equipped with
”High Power”-outputs. Only with a few older and head units the Auto Turn On function is not working.
VARIABLE SUBSONIC FILTER
WiththeSUBSONICcontroller(Fig.1,5)youcanadjustthelowercrossoverfrequency,toltertheverylow
frequencies to relieve the subwoofer or to generate a bandpass signal. If you don’t want to use this function,
turn the controller (Fig. 1,5) to the very left to the 10 Hz position.
NOTE: The adjusted value of the SUB SONIC (Fig. 1,5) should not be higher than the adjusted value of the
LOW PASS controller (Fig. 1,4). Otherwise no sound will be audible.
VARIABLE LOW PASS FILTER
Set the desired crossover frequency by using the controller LOW PASS (Fig. 1,4). Thus to that only the fre-
quenciesbelowthechosencrossoverfrequencywillbeampliedandthesubwooferplaysmorepreciselyand
efcient.
BASS LEVEL REMOTE CONTROLLER
With the included bass level cable remote controller you are able to adjust the bass level e.g. out of the driver’s
seat. Connect the remote controller and the REMOTE connector (Fig. 1,2) with the enclosed cable.
PHASE SHIFT CONTROLLER
The PHASE SHIFT controller (Fig. 1,6) allows to adjust the phase between 0° and 180° to match the output
signal with the vehicle’s interior acoustic.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX SXE1200.1D at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX SXE1200.1D in the language / languages: English, German as an attachment in your email.

The manual is 3,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info