168695

ESX se 5800 Manual

21
Zoom out
Zoom in
Previous page
1/28
Next page
INTERCONNECTION LINE INPUTS
• Connect the RCA lineouts of the headunit with the RCA jacks LINE INPUT of the amplifier with appropriate high-value RCA cables.
INTERCONNECTION SPEAKERS
• Connect the front- and rear speakers with the speaker outputs (SPEAKER OUTPUT + 1CH -, + 2CH - and + 3CH -, + 4CH -).
• Ensure by any means, that the total impedance load of all speakers is not lower than 2 ohms. Too low impedance cause high temperature
and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
INTERCONNECTION SUBWOOFER
• Connect the subwoofer with the speaker outputs (SPEAKER OUTPUT + 5CH -) of the amplifier.
• Ensure by any means, that the total impedance load of of the subwoofer is not lower than 1 ohm. Too low impedance cause high
temperature and will shut down the amplifier operation.
• Always ensure the correct polarity of the speakers. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
MODE SWITCH
• Select the 5CH position on the MODE switch in this example. If headunit is not equipped with a separate subwoofer output (SUB OUT),
connect the CH1/2 and CH3/4 RCA line inputs and select the 4CH position. Thereby the input signal on CH1/2 and CH3/4 will be routed
to the subwoofer channel (CH5) and the subwoofer signal will be filtered out.The use of Y-connectors is not required in this case.
CROSSOVER SETTINGS CH1/2 & CH3/4
• By using bigger speakers (more than 20cm) you can set the X-OVER switch to the FULL position (Full Range Signal).
• By using smaller speakers (8.7cm - 16cm) you must set the X-OVER switch to the HP Position (Highpass Mode) to avoid any damage
by lower frequencies on the speakers. The cut-off frequency is adjustable with the HPF controller and should be set between
60Hz to 150Hz, depending on the size of the speakers.
LOW PASS CONTROLLER Subwoofer Channel CH5
• The LOW PASS controller adjusts the cut-off point of the frequency range to above. The cut-off frequency is continuously
adjustable from 35 Hz to 250 Hz.
SUBSONICFILTER CONTROLLER Subwoofer Channel CH5
• The SUB SONIC controller (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal to below, to avoid a
mechanical and electrical overloading on the subwoofer. The cut-off frequency is adjustable from 15 to 55 Hz and depends on the size
of the subwoofer.
BASS BOOST CONTROLLER Subwoofer Channel CH5
• The BASS BOOST controller adjusts the bass enhancement between 0db and +12dB.
• A too high bass boost may cause clipping/distortion and damage on the loudspeakers and also may harm your hearing abilities.
Use this controller carefully!
BASS REMOTE CONTROLLER Subwoofer Channel CH5
• The enclosed BASS REMOTE Controller adjusts the subwoofer level e.g. from the driver’s seat.
Please use only the enclosed bass remote controller and cable.
LEVEL CONTROLLER CH1/2, CH3/4 and CH5
• Turn the LEVEL controller of the amplifier to the 5V position.
• Turn the volume controller of the headunit to 80 - 90% of its full setting.
• Turn the LEVEL controller clockwise until you hear some distortion.
• Then turn back the LEVEL controller slightly until you hear a cleaner sound.
SE5800
21
INTERCONNECTION EXAMPLE 5-Channel Mode: Stereo Front- & Rearsystem + Subwoofer
Do not connect loudspeaker cables with the vehicle’s chassis. Always ensure the correct polarity
of all connections. The interchange of plus and minus cause total loss of bass playback and could
damage the speakers.
REFERENCE NOTE
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX se 5800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX se 5800 in the language / languages: English, German as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info