168695
19
Zoom out
Zoom in
Previous page
1/28
Next page
1 42 5 6 7 2 3 103 948
1
9
POWER/PROTECT (Also located on the Bass Remote unit)
If the POWER LED lights up, the amplifier is ready for operation.
If the PROTECT LED lights up, a malfunction is indicated. Attend in this case the chapter TROUBLE SHOOTING.
10
3
The BASS BOOST CH5 controller adjust the bass boost enhancement on the subwoofer channel (CH5) continuously from
0dB to +12dB at 45 Hz.
2
The CH1/2 and CH3/4 X-OVER switch selects the required operation mode of the amplifier on the regarding channel pair
(Channel 1/2 or Channel 3/4).
Position HP: Highpass mode (The higher frequencies will be eliminated. Adjustable by the HPF highpass controller.)
Position FULL: Fullrange mode (The whole frequencies will be amplified).
7
The LPF (Lowpassfilter) CH5 controller adjust the cut-off point of the frequency range for the subwoofer channel (Channel 5)
to above. The cut-off frequency is continuously adjustable from 30 Hz to 150 Hz.
8
The INPUT MODE switch must be in 4CH position, if you connect only two RCA stereo audio cables with the CH1/2 and CH3/4
line inputs. Select the position 5CH, if you connect three RCA stereo audio cables with CH1/2, CH3/4 and CH5 line inputs.
Therefor the additional available subwoofer lineout (SUB OUT) of your headunit on input CH5 is recommended.
If you select the 4CH mode, the input signal of LINE INPUT CH1/2 and CH3/4 will be routed to the subwoofer channel CH5.
The subwoofer signal will be filtered out of the incoming signal. Due to this, only two RCA stereo audio cables are required and
no Y-Adaptors are required.
4
The REMOTE port is for the cable of the enclosed bass remote controller. With this bass remote controller, you are able to
adjust the bass level on the subwoofer channel (CH5) e.g. from the driver’s seat. Please use only the enclosed bass remote
controller and cable.
6
The HPF(Highpassfilter) CH1/2 and CH3/4 controllers adjust the cut-off point of the frequency range to below for the regarding
channel pair (Channel 1/2 or Channel 3/4). The cut-off frequency is continuously adjustable from 10 Hz to 150 Hz .
5
The LEVEL CH1/2, CH3/4 and CH5 controllers adjust the input sensitivity of the amplifier to align the audio signal of the head
unit for the regarding channel pair (Channel 1/2, 3/4 or 5). The input sensitivity is adjustable from 5 to 0.2 Volts.
The LINE INPUT RCA jacks must be connected with the RCA output jacks of the headunit.
By connecting only the CH1/2and CH3/4 jacks, the MODE switch must be set to the 4CH position.
The SUB SONIC controller (Subsonicfilter) limits the ultralow and not hearable frequencies of the audiosignal on the subwoofer
channel (5CH) to below, to avoid a mechanical and electical overloading on the subwoofer. The cut-off frequency is adjustable
from 15 to 55 Hz and depends on the size of the subwoofer.
SE5800
19
FUNCTIONS AND OPERATIONAL CONTROLS
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX se 5800 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX se 5800 in the language / languages: English, German as an attachment in your email.

The manual is 2,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info