700183
21
Zoom out
Zoom in
Previous page
1/24
Next page
21
ENGLISH
TROUBLE SHOOTING
ELECTRICAL INTERFERENCES
The reason for interferences are mostly the routed cables and wires. Especially the power and audio cables (RCA) of your sound system
are vulnerable. Often these interferences are caused by electric generators or other electrical units (fuel pump, AC etc.) of the car. The
most of these problems can be prevented by a correct and careful wiring.
Here are some courtesy notes:
1. Use only double or triple shielded audio RCA cables for the connection between the amplier and head unit. An useful alternative
are represented by anti-noise-devices or additional ancillary equipment like Balanced Line transmitters, which you can purchase
at your car audio retailer. If possible do not use anti-noise-lters, which are splicing the ground of the RCA audio cables.
2. Do not lead the audio cables between the head unit and the amplier together with the power supply wires on the same side of
the vehicle. The best is a real separated installation on the left and right cable channel of the vehicle. Then the overlapping
of interferences on the audio signal will be avoided. This stands also for the enclosed bass-remote wire, which should not be installed
together with the power supply wires.
3. Avoid ground loops by connecting all ground connections in a starlike arrangement. The suitable ground center point is
ascertainable by measuring the voltage directly on the vehicle’s battery by a multi-meter. You should measure the voltage with
turned-on ignition (acc.) and with other turned-on power consumers (e.g. headlights, rear window defroster, etc,). Compare
the measured value with the voltage of the ground point you have chosen for the installation and the positive pole (+12V) of
the amplier. If the voltage has just a little difference, you have found a suitable ground point. Otherwise you need to choose an
other ground point.
4. Use if possible only cables with added or soldered cable sockets or the like. Gold plated or high value nickel plated cable sockets
are corrosion free and own a very low contact resistance.
PROTECTION CIRCUIT
This amplier owns a 3-way protection circuit. On overloading, overheating, shorted loudspeakers, too low impedance or insufcient
power supply, the protection circuit turns off the amplier to prevent serious damage. If one of this malfunctions is detected, the POWER/
PROTECT LED lights up red.
In this case, check all connections to detect short-circuits, faulty connections or overheating. Refer to the notes on the next page.
If the reason for the disfunction is eliminated, the amplier is ready for operation again.
If the red the POWER/PROTECT LED does not stop to light up in red, the amplier is damaged. In this case return the amplier to your
car audio retailer with a detailed malfunction description and a copy of the proof of purchase.
WARNING: Never open the amplier and try to repair it by yourself. This causes a loss of warranty. The repairing service should be made
only by skilled technicians.
INSTALLATION AND OPERATION IN NEWER VEHICLES!
In many vehicles (since approx. 2002) computer controlled diagnosis- and controlling systems are applied - like CAN-BUS or MOST-BUS
interfaces. With the installation of a car audio amplier a new appliance will be added to the 12V on-board electrical system, which may
cause under several circumstances error messages or may interrupt the factory made diagnosis system, as a result of high stress peaks
and a higher power consumption. Thus, depending on model and manufacturer, the driving safety or important security systems like
airbags, ESC or others could be interrupted.
If you plan to operate the amplier in a vehicle like described above, please follow these instructions:
Let the installation be made only by a skilled specialist or a service station, which is specialized for the maintenance of your vehicle.
After the installation, we suggest to make a computer diagnosis of the on-board system, to detect possible malfunctions or errors.
If the on-board system is interfered by the installation of the amplier, an additionally installed power capacitor can stabilize the electrical
on-board system to ensure a proper and stable operation.
The best solution is the integration of an own additional 12 V electrical system for the sound system, which can be operated
independently with an own battery supply.
CONSULT YOUR CAR SPECIALIZED SERVICE STATION!
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX QE1200.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX QE1200.4 in the language / languages: English, German as an attachment in your email.

The manual is 3,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info